05/04/2024
SMALL MUD ROTARY RIGS
SEISMIC MODEL 10 DRILLING RIG (Ref#4188T)
Rotary table drive, Gardner Denver 5 x 6 FG-41 mud pump, Ingersoll Rand Type 40 air cooled air compressor, munted on 1979 GMC Brigadier J9500 tandem axle truck, 30’ x 9’ x 11’ (10’ with Kelly and lights removed) Price: $41,000
Available at extra cost:
1980 GMC C6500 SERVICE TRUCK (Ref#4188Tb) 300 gal water tank, 100 gal fuel tank, oxy-acet torch, mounted tool lockers with some tools
24’ CASING TRAILER (Ref#4188Tc)
PLAIN STATES MFG A30 DRILLING RIG (Similar to Gus Pech) (Ref#8886T)
Built 1990, good for small spaces, 80 cfm hydraulic air compressor, 4 x 2 centrifugal mud pump, 2 winch cables, mounted on single axle 1990 International 4x2 truck with diesel engine, PTO, mud pump, stabilizer, rod box, mud pan, surface tube, approximately 200’ of 5’ rods, 8-3/4” bit, 10’ stabilizer, breakaway hydraulic wrench, 2 rear hydraulic leveling jacks, motor rebuilt 2022 and has drilled 5 wells since Price: $37,500
GARDNER DENVER 1500HD (Ref#4198RA)
Manufactured 1975, double drum, refurbished, air compressor (PTO), 5-1/2 x 8 mud pump, mounted on 1975 International with 6 cyl Detroit diesel engine, 38'9" derrick, 3 lines to hook, 3" swivel (reduced to 2" mud hose), 3-1/2" fluted kelly, 5 ½" stationary table, pipe rack, no pipe available Price: $87,500
MAYHEW 1500 (Ref#15697T)
Detroit 671 diesel deck engine, no mud, no air compressor, retractable table, 26’ square Kelly (can run 33’ casing), mounted on 1981 GMC Brigadier with Cat 3208 engine, pipe racks (holds approx. 500’), hydraulic breakout, hydraulic pulldown, air clutches, 3 leveling jacks, 900’ drill pipe, 22’ 3-axle trailer, (2) 4-1/2” x 20’ drill collars, (1) 5-1/2” x 30’ drill collar, misc change overs and pick up plugs Price: $54,500
GARDNER DENVER 15W DRILL RIG (Ref#2000T)
Manufactured 1980’s, Range 1, 600/250 air compressor, (2) 5 x 6 mud pumps, 10” retractable table, geolograph, mounted on 4-axle Crane Carrier, 1200’ of 2-7/8” IF Range 1 drill pipe, includes a 1991 Volvo tandem axle pipe truck with 20’ bed Price: $165,000
GARDNER DENVER 15W (Ref#2521T)
GARDNER DENVER 15W (Ref#10468T)
Manufactured 1977, Cummins 400 Big Cam 3 engine (less than 300 hours since in frame), 5-1/2 x 8 Gardner Denver mud pump, Gardner Denver WEJ 750/250 air compressor with blower, 52' x 100,000# 4-line derrick, 2500' racking board, hydraulic power tongs range 2-3/8 – 4-1/2, mounted on 4 axle Crane Carrier, 4 cylinder Bean mist pump, hydraulic hydramatic trip hold back, hydraulic kelly hold back, 4-1/2" square kelly with kelly cock, 10" Gardner Denver rotary table, swabbing drum with 2000' cable.
Drill pipe: 2000' of 2-7/8" x 20' (2-3/8 IF thread), 800' of 3-1/2" x 31' (3-1/2 IF thread)
Drill collars: 100' 3-3/4" x 20' (2-3/8 IF thread), 100' 4-1/2" x 20' (2-7/8 IF thread), 100' 6-1/4" x 20' (4-1/2 H90 thread)
Substructure: 5'H x 10'W x 44'L with retractable axle
Sullair 900 hp air compressor 350 psi (low hours)
5" x 10" Gaso skid mounted mud pump powered by 471 Detroit engine
5'H x 10'W x 42'L 300 bbl mud pit with hopper
5'H x 10'W x 42'L 330 bbl mud pit
7" Swaco rotating head
7" Hydrill BOP
35' tandem float pipe trailer with 4' x 8' parts house
1973 International water truck, 80 bbl with 355 Cummins engine
1968 Chevrolet 2-1/2 ton fuel truck with (4) 500 gal compartments
8' x 15' tandem crew trailer
2 pin Totco geolograph
Totco degree survey tool
Hydraulic survey machine with 8000' of high tensel steel line
8' x 40' shop made horizontyal drilling rig has drilled to 1800'
Tools, parts, X over subs, etc and more
PRICE RIG ONLY; $245,000
Package Price: $650,000 REDUCED: $525,000
GARDNER DENVER 15W (Ref#748T) 5 x 8 mud pump, 54’ mast, 8” retractable table, mounted on Crane Carrier, 400 Cummins engine, 1400’ drill pipe
7 x 16 Gardner Denver mud pump (no engine)
Package Price: $225,000
GARDNER DENVER 15W (Ref#15089R)
Manufactured 1978, 5-1/2 x 10 Gardner Denver mud pump, no air compressor, 10" retractable table, mounted on 1977 Autocar with 400 Cummins engine, PTO, air clutches, 58' extended mast, 4-1/2" x 24' kelly (smaller kelly available), piep rack, breakout tongs, racking boards, chain pulldown, 5 hyd levelng jacks Price: $165,000
GARDNER DENVER 15W DRILL RIG (Ref#8644Ta)
60’ mast (was extended 10’), 10” table, 5 x 6 mud pump, mounted on 1964 GMC White tandem axle truck with GMC engine, PTO, leveling jacks, not used since 2019, 2nd owner rig Price: $90,000
GARDNER DENVER 1400 (Ref#2084T)
5 x 8 Gardner Denver mud pump, 8-1/2” Midway rotary table (rebuilt), 44’ new derrick, 2-1/2” Little Giant swivel, mounted on 1998 Freightliner truck with diesel engine, new 22’ fluted kelly, friction clutches, rod rack, , Davey drop box Price: $112,500
MAYHEW/GARDNER DENVER 1000 MODIFIED (Ref#2945T)
Mounted on 2009 Peterbilt 340 double frame carrier, 5 x 6 mud pump (fluid and mechanical ends reworked), no air compressor, drawworks and brake linings reworked, pulldown reworked, new cutch linings, 3.5” swivel, 5-1/4” stationary rotary table, new kelly and sandline cable and hardware, chain pulldown, dual driller’s platforms, 3 hydraulic jacks, 380’ 2-3/8” Mayhew Jr drill pipe, 8” and 10” drill bits Price: $225,000
GARDNER DENVER 1000 DRILL RIG (Ref#9524T)
Manufactured 1981, completely rebuilt 2010, 5 x 6 mud pump, 667 air compressor, retractable table, mounted on 2010 Freightliner with Cummins engine, PTO, 25,000 miles, 4 jacks, engine burns 2.6 gal per hour Price: $235,000
GARDNER DENVER 1000 DRILL RIG (Ref#9790Ta)
Manufactured 1972, 550/150 air compressor, 4 x 3 Mission centrifugal mud pump, mounted on tandem axle Ford truck, 700’ of 3” Bottleneck x 20’ (2-3/8 IF) drill pipe, 6” collar, (2) 7-7/8” tricone bits, starter subs, handling tools and slips, ready to work Price: $164,500
MAYHEW 1000 DRILL RIG (Ref#7762Tb) 5 x 6 mechanical mud pump, 5-1/2” fixed table, 40-500 Geoloop grouter, mounted on 1993 International 9400 truck with Cummins M11 diesel engine, PTO, 280’ of 2-7/8 x 20’ drill pipe, running rig Price: $83,500
MAYHEW 1000 DRILL RIG (Ref#3934T)
GARDNER DENVER 1000 (Ref#9505R)
Mounted on Mack truck, 5 x 6 mud pump, 667 air compressor, 7-1/2” rotary table, rod rack, 3 leveling jacks Price: $77,500
MAYHEW 1000 DRILL RIG (Ref#4401Ta)
Gardner Denver mud pump, stationary table, 2-7/8" kelly, mounted on 1977International truck, approx. 300’ 2-7/8" drill pipe, 7-7/8" & 9-1/4" bits, running condition Price: $62,500
MAYHEW 1000 DRILL RIG (Ref#5538T)
GARDNER DENVER/MAYHEW 1000 DRILL RIG (Ref#8294Ta)
MAYHEW 1000 DRILL RIG (Ref#3957T)
5-1/2” stationary table, Gardner Denver 5 x 6 mud pump (new liners, pistons & rods), 3-1/2” x 26’ kelly, Western Star winch, mounted on 1999 Volvo truck with Cummins diesel engine, 260’ of 3” x 20’ slick drill pipe, includes extras and parts, Geo-Loop 40-500 grout pump Price: $93,500
MAYHEW 1000 DRILL RIG (Ref#8661T)
Unmounted, 5 x 6 mud pump, Leroi air compressor, 2000 DSM table, hydraulic pulldown, mechanical clutches, 2-7/8” kelly, 4 hydraulic leveling jacks, no pipe or tools Price: $162,500
MAYHEW 1000 (Ref#15274T)
GARDNER DENVER 1000HD (Ref#15652T) Manufactured 1979, 5 x 6 Failing mud pump, Leroi developmental air compressor, 23’ fluted kelly, 7-1/2” retractable Speedstar table, hydraulic pulldown, air over hydraulic clutches, pipe rack, breakout wrench, mounted on International truck with DT466 engine, 3 hyd jacks, 300’ of 20’ pipe
Freightliner water truck with (2) plastics tanks, 2600 gallons total, diesel engine
Package Price: $70,000
MAYHEW 1000 DRILL RIG (Ref#5244T) Gardner Denver 5 x 6 mud pump, no air, stationary rotary table, mounted on single axle truck with diesel engine, 2 rear hydraulic leveling jacks, running condition, 800’ of 2-7/8” x 20’ pipe on trailer Price: $58,500
MAYHEW 1000 (Ref#15087T)
Manufactured 1957, 5 x 6 Gardner Denver mud pump (new gear end and fluid end) valves on pump are missing, Gadner Denver WEQ developmental air compressor, 7-1/2” retractable table, 24’ kelly, 35’ mast, chain pulldown with hydraulic motor, mounted on 1973 Diamond Rio double frame, 290 Cummins engine, 8 speed transmission, engine and transmission new, heavy duty PTO, 2 rear and 1 front leveling jacks, 300’ of 2-3/8” drill pipe, mud pan, 2 bits, ready to work, new cables Price: $42,500
MAYHEW 1000 (Ref#11322T) Mounted on 1994 Ford truck, Cat engine, 7-1/2” table, 5 x 6 Gardner Denver mud pump, 23’ kelly, 2” swivel, hydraulic pulldown, water injection pump, 3 leveling jacks Price: $60,000
MAYHEW 1000 (Ref#8472T) Set up for drilling and workover, 4” square kelly, stationary table, mounted on 1974 International Lodestar, 5 x 6 Gardner Denver mud pump, no rod box, breakout tongs, 400’ of 2-3/8” x 20’ drill pipe, 10” surface bit, (2) 4” drill collars, 11 new button bits, 3 axle pipe trailer Price: $44,500
GARDNER DENVER 1000 (Ref#13496T) Manufactured 1979, 5 x 6 mud pump, 200 cfm air compressor, 5-1/2" retractable table, 3-3/4" x 23' fluted kelly, hydraulic pulldown, mechanical clutches, pipe rack, pipe wrench, mounted on 1979 Ford 9000 truck with Detroit 6V92, 4 hyd jacks, drills daily Price: $112,500
MAYHEW 1000 (Ref#891Ta) Manufactured 1978, 5 x 6 Gardner Denver mud pump, Gardner Denver air compressor, 5-1/4" stationary table, mounted on 1997 International truck with Cummins engine, 10 speed transmission, 30' mast, 25' kelly, chain pulldown, 2 rear leveling jacks, 300' of 2-7/8" IF drill pipe Price: $79,500
MAYHEW 1000 (Ref#891T) 5 x 6 Gardner Denver mud pump, IR air compressor, 7-1/2" Mayhew rotary table, 30' mast, 25' kelly, chain pulldown, air clutch, mounted on 1996 Ford LT9000 truck with Cummins engine, 2 rear jacks, 300' drill pipe Price: $89,500
MAYHEW 1000 (Ref#11597R)
Manufactured 1970, only 200 hours since in-frame overhaul, mounted on 1970 GMC with straight 671 Detroit engine, 5x6 GD mud pump, GD 580 air compressor, 18' kelly, hydraulic pulldown, mechanical clutches, breakout tongs, pipe rack, 1 front screw jack & 2 rear hydraulic leveling jacks, 150' of 2 7/8"IF x 15' drill pipe Price: $47,500
MAYHEW 1000 DRILL RIG (Ref#4022T)
MAYHEW 1000 (Ref#3870R)
Air compressor, 5 x 6 mud pump, 23' kelly, 7-1/2" rotary table, mounted on 1996 International truck with Cummins 350 hp engine, 300' of 2-7/8" OD with 2-3/8 IF drill pipe, air clutches Price: $90,000
MAYHEW 1000 (Ref#5199R)
5 x 6 Garnder Denver mud pump, Gardner Denver air compressor, 5-1/4" stationary rotary table, mounted on 1997 Ford L9000 truck with Cummins 350 hp diesel engine, chain pulldown, 23' kelly, new brakes, new drums, new kelly bushings Price: $75,000
MAYHEW 1000 (Ref#10021N)
mounted on Rio 6x6 with Cat 3306 rebuilt engine, Fuller 10 speed transmission, Gardner Denver 5 x 6 mud pump, Leroi 100s air compressor, 2000 stationary table, 3 ½" x 23' Kelly, water injection pump, 500 gallon water tank, hydraulic pulldown, mechanical clutches, breakout wrench, 2 rear hydraulic leveling jacks, 200 of 2 7/8" x 20' drill pipe and International
Price: $55,000
MAYHEW DSM 1000 DRILL RIG (Ref#5483T)
Completely refurbished 2010, derrick needs a little work, Mission Magnum Sandmaster 4 x 3 x 13 mud rotary pump, mounted on 1998 Mack CH613, completely with 2-3/8 pipe and various bits Price: $167,500
MAYHEW 1000 (Ref#2362N)
PTO, mounted on 1971 White Constructor with 290 Cummins engine, 6 x 6 Wheatley mud pump, 580 CFM air compressor, custom made 42’ mast, 36’ Kelly, stationary table, mechanical clutches, pulldown, 1 front 2 rear hydraulic leveling jacks, no breakout wrench, no pipe or tools available Price: $42,500
SHOP BUILT RIG - SIMILAR TO MAYHEW 1000 (Ref#6809T)
MAYHEW 1000 COMBINATION RIG (Ref#1790Na)
Manufactured 1970, PTO, mounted on 1970 Chevy with gas engine, 5 x 6 Gardner Denver mud pump, 185 CFM on board air compressor with John Deere diesel engine, spudding arm, 5-1/4" stationary table, hydraulic pulldown, 3 hydraulic leveling jacks, 23' Kelly, 210' of 2 3/8" x 15' drill pipe, stabilizer PRICE ON REQUEST
GARDNER DENVER 500 DRILLING RIG (Ref#6493T)
Manufactured 1976, 100 cfm air compressor, grout mixer, mounted on 1997 Ford F800 truck with approx. 240,000 miles, 8.3 Cummins engine, lightweight, used as training rig in a drilling school, 3” x 15’ flush wall pipe w/FEDP threads Price: $100,000
MAYHEW 500 DRILL RIG (Ref#8641T)
Gardner Denver 5 x 6 mud pump, 100/150 Gardner Denver air compressor, 5-1/2” retractable table, 20’ kelly, air engaged mud pump and table, mounted on 1998 Volvo with M11 Cummins engine, 390’ of Mayhew Reg drill rod, lockers, ready to work Price: $120,000
MAYHEW 200 (Ref#10635R)
Manufactured 1974, diesel rig engine (blown head gasket, needs work), mounted on Ford F600 truck with 390 gas engine, 3 leveling jacks, 600’ of 2-3/8” x 10’ drill pipe, no pulldown (can put back), truck does not run, sitting a while Price: $13,000
SPEEDSTAR SS-135 DRILL RIG (Ref#3648T)
SPEEDSTAR 135 (Ref#3612T) (2) 5 x 6 Gardner Denver mud pump, 7-1/2" rotary table, chain pulldown, 7 speed transmission, 466 engine (210 hp), 1991 International truck, 4 leveling jacks Price: $95,000
SPEEDSTAR SS-135 DRILL RIG (Ref#11810Ta) Manufactured 1976, 5-1/2 x 8 mud pump, 8-1/2” DSM retractable table, mounted on 1994 Ford LN9000 truck with Cat 3306 engine, breakout wrench, rod box, 4 hyd leveling jacks, tools, 1000’ of 20’ 3-1/2” flush wall drill pipe, ready to work Price: $112,500
SPEEDSTAR SS-135 (Ref#3879TA)
290 cfm air compressor, John Deere deck engine for compressor, 8-1/2” retractable table, hydraulic pulldown, 5 x 6 Gardner Denvermud pump, mechanical clutches, mounted on tandem axle 1997 International 9400 truck with DT466 engine, approx 500’ rods, some tools, good condition, ready to go Price: $102,500
SPEEDSTAR 135SS DRILLING RIG PACKAGE (Ref#14196T) Manufactured 1969, mounted on 1998 International 4900 truck, 9 speed transmission, tires 90%, PTO, 7-1/2” retractable rotary table, kelly/swivel, 2 rear hydraulic jacks, 5 x 10 Gaso 300 gpm mud pump (gear end 95%)
800’ of 2-3/8 IF drill pipe (pipe less than one year old)
1998 International 4900 water truck with DT466 engine, 9 speed, tires 90%, 2200 gallon
Package Price: $220,000
SPEEDSTAR SS-210 ROTARY DRILLING MACHINE (Ref#5583T)
Manufactured 1974, Gardner Denver WEJ 1009 air compressor with second stage cooling, Gardner Denver FG-FXF 5 x 6 mud pump, mounted on 1974 Crane Carrier with 8V71N diesel engine (motor refurbished), less than 10,000 miles, PTO, air line lubricator, water injection pump, double drum drawworks, single line pull 15,000#, friction clutches, large brakes, sandreel drum 8000# capacity, 8-1/2” retractable rotary table, pulldown, 2” pitch feed chains, 35’ heavy duty derrick, 4-1/4” x 24’ round kelly bar, 2” water swivel, pipe rack Price: $115,000
SPEEDSTAR GEFCO SS-15-III DRILLING RIG (Ref#8735T)
Manufactured 1989, 3 drum drawworks, (2) 5 x 6 deck mounted mud pumps, 500/200 Sullair compressor (new year 2000), 5” fluted kelly, hydrostatic 8” rotary table, set up for mud drilling and reverse air drilling, pulldown, hydrostatic over-air clutch, mounted on 1988 Peterbilt truck, rebuilt engine in 2017 with approx. 400 hours) Price: $195,000
SPEEDSTAR SS15-III DRILL RIG (Ref#6805T) Manufactured mid 1980’s, 7-1/2 x 8 mud pump, no air, mounted on International truck with diesel engine, PTO, 4 hydraulic leveling jacks, some pipe, rotary table was removed (needs repair or replacement), no rod box Price: $124,500
SPEEDSTAR SS-15-II DRILL RIG (Ref#7154T)
Manufactured 1976, 3 x 5 mud pump, no air compressor, Cat engine, 400 Cummins, rebuilt 10” rotary table, rebuilt hydraulic drive, fair condition, 380’ of 2-7/8 drill pipe Price: $100,000
SPEEDSTAR SS-15 (Ref#14222Ta)
Gardner Denver 5 x 8 FXX172 mud pump, air compressor, 9" retractable table, 40' mast, pulldown, mounted on 1977 Crane Carrier, Cummins 855 diesel engine, 3 hyd leveling jacks, drill pipe Price: $115,000
SPEEDSTAR SS15-III DRILL RIG (Ref#9337T)
Manufactured 1977, LeRoi 256-S2 450/250 air compressor, 4 x 4 x 13 centrifugal pump (he uses for drilling), mounted on 1977 GMC 9500 truck with 290 Cummins engine, PTO, rod box, leveling jacks, no carousel, 300’ of 3-1/2” x 20’ flush wall drill pipe, good shape, running rig, handling tools, bits Price: $60,000
SPEEDSTAR SS-15 (Ref#10125T)
Manufactured 1977, PTO, mounted on 1977 CCC with 290 Cummins engine, 3x4 centrifugal mud pump, Leroi 500/100 air compressor, 8-1/2" retractable table, 4-1/4" x 23' kelly, breakout wrench, pipe rack, 1 front & 2 rear hydraulic leveling jacks, 300' of 4-1/2" x 20' drill pipe, needs new truck Price: $39,500
SPEEDSTAR SS-15-II DRILL RIG (Ref#7966T)
Manufactured 1976, Mounted on CCC with diesel engine, PTO, 5 x 6 piston mud pump, 8-1/2” retractable table, sandreel, line oiler, breakout wrench, 4” x 23’ kelly, chain pulldown, mechanical clutches, pipe rack, mud pump, compressor available but removed, running condition Price: $97,500
SPEEDSTAR 1500 (Ref#3153T) 500/250 air compressor, no mud pump, rotary table, mounted on Mack truck with diesel engine, PTO, front wheel assist, rod rack, 700’ drill pipe Price: $72,500
SPEEDSTAR 1300 DRILL RIG (Ref#9554T)
Manufactured 1970’s, 5-1/2 x 6 Gardner Denver mud pump, no air, 5” retractable table, 25’ fluted kelly, mechanical clutches, pulldown, mounted on Ford 900 tandem axle truck with diesel engine, breakout wrench, pipe rack, 1 front manual leveling jack, 2 rear hydraulic leveling jacks, 300’ of 20’ drillpipe (2-3/8 IF), last ran in 2022 but starts it up occasionally. Price: $47,500
SPEEDSTAR SS1000 DRILL RIG (Ref#3669T)
Manufactured 1983, Gardner Denver 5 x 6 mud pump, retractable table, mounted on International 4900 tandem axle truck with 251,000 miles, 4 jacks Price: $70,000
CHALLENGER DRILLING RIG (Ref#4787T)
Manufactured 1979, mounted on International Paystar 5000 with 350 Big Cam Cummins engine, PTO, centrifugal mud pump, pipe rack, 3-1/2IF 20’ drill pipe, currently drilling. Also includes unounted Gardner Denver 5-1/2 x 8 mud pump Price: $144,500
FAILING 1500 DRILL RIG (Ref#2387T)
Rig and truck reworked in 2022, HD drawworks, dual band brakes, 3rd line, 5 x 6 Gardner Denver mud pump, 8” rotary table, 2-7/8” kelly, chuck pulldown, mechanical clutches, mounted on 1999 International tandem axle truck with 300 hp diesel engine, full locking tandem axles, 10 speed transmission, 4 leveling jacks, PTO, deck space, tool boxes, custom rod chute, breakout wrench, no pipe (uses 20’ rods) Price: $144,500
FAILING 1500 DRILL RIG (Ref#1375Tb)
750/125-250 air compressor, 7” retractable table, Little Giant swivel, 400’ of 2-7/8 flush joint pipe, mounted on 3 axle Peterbilt, 6V71 Detroit Price: $110,000
FAILING 1500 (Ref#3881NA)
Manufactured 1989, PTO, mounted on 1981 International with Cummins engine, 4x3 centrifugal mud pump, 900 CFM air compressor, hydraulic pulldown, mechanical clutches, 4-1/2" retractable table, 3-1/4" x 25' Kelly, chain pulldown, 3 hydraulic leveling jacks, rod box, portable mud pit, 200' of 3-1/2" IF x 15' drill pipe Price: $115,000
FAILING 1500 DRILL RIG (Ref#13791R)
Manufactured 1970's, mounted on 1991 International with DT466 engine, 4 -1/2 x 5 Failing mud pump, auto chucks, 32' mast, 17' x 2 3/8" kelly, 2 leveling jacks Price: $37,500
FAILING 1500 (Ref#2827R)
1500 retractable table, 2-3/8" kelly, mechanical clutches, 5 x 6 Gardner Denver mud pumps, mounted on 1978 I6000 truck, Cat diesel engine, needs work (fluid ends needs rebuildeing, needs new hydraulic banks) Price: $49,000 PRICE REDUCED: $34,500
FAILING 1500 (Ref#4674N)
1500 drawworks, PTO, mounted on 1996 International 4700 4x2 truck with DT466 engine, (2) drilling pumps: Failing L100 800 max test pressure, 350 max working pressure and Gardner Denver FFFXFM 148.5 gpm, 639 max pressure, retractable table, mechanical clutches, hydraulic pulldown, 2 3/8” Kelly, 1 front & 2 rear hydraulic leveling jacks Price: $38,500
FAILING 1500 DMX DRILL RIG (Ref#9268Ta) Mounted on 1986 International truck with DT466 diesel engine (low hours after rebuild), PTO, non-retractable rotary table with 2 pins to handle 6” casing, (2) 5x6 mud pumps (clutch needs work, 4-1/2” x 20’ kelly, 300’ of 20’ drill pipe (2-7/8 IF), double drum, 4 leveling jacks, last drilled 2016 Price: $69,500
FAILING 1500 DRILL RIG (Ref#9268Tb) Reworked in 1985, mounted on International tandem truck with DT466 diesel engine, friction clutches, 40’ mast, double drum, 5 x 6 mud pump, 300’ drill rod Price: $64,500
FAILING 1500 (Ref#7758T) 8” retractable table, Ford gas deck engine, mounted on 10 wheeler with gas engine, 3 hyd leveling jacks, no rod box or pipe rack, incluees 390’ of FEDP pipe, 14” bit Price: $19,500
FAILING 1500 DRILL RIG (Ref#2826T)
FAILING 1500 DRILL RIG (Ref#2826T) Gardner Denver FXG-172 mud pump, no air compressor, mounted on single axle White truck with diesel engine, PTO, pipe and tools, running condition Price: $23,500
FAILING 1500 DRILL RIG (Ref#7544Tb)
Mounted on 1964 Chevy truck, 7-1/2” x 8 GD FXX172 mud pump, 42’ derrick (2-sections), hydraulic pulldown, 30” stroke, hydraulic table Price: $87,500
FAILING 1500 (Ref#7797N)
Manufactured 1966, 5-1/2 x 8 mud pump, mounted on 1972 Brockway 10 wheeler truck with 781 Detroit diesel, PTO, 23’ kelly, 8-1/2” rotary table, breakout table, mechanical pulldown, mechanical clutches, hydraulic quills, 3 jacks, runs 20' drill pipe (no pipe included) PRICE: $64,000
FAILING 1500 HOLEMASTER (Ref#8617R)
Manufactured 1964, 5 x 6 mud pump, 2-3/8” kelly bar, 6" rotary table, heavy duty mast, 2 winches w/15” clutch, hydraulic pulldown, mounted on 1964 International truck, PTO, double plated frame, 304 International engine, needs minor repairs
1000’ 2-3/8” x 20’ drill pipe with Acme threads (3 TPI)
1979 Ford FL7000 water truck, flat bed, 1800 gal water tank, Cat 3208 engine
Package Price: $62,500
FAILING CF15 (Ref#557Ta)
2006, trailer mounted, Gardner Denver 5-1/2 x 8 mud pump, 39’ x 45,000# tubular steel mast, low hours, located Texas Price: $190,000
FAILING CF15 DRILL RIG (Ref#5513T)
5 x 6-1/4 Failing chain driven mud pump (rebuilt)551, new clutch plates and bearings, Leroy 256 2-stage air compressor, DSM retractable rotary table, air clutches, pulldown, new FMC Bean pump in 2020, new Kelly hose, new gears on pulldowns, new input shaft on transmission, mounted on 1977 International Paystar with Cummins diesel, breakout wrench, rod box, 400’ of 3-1/2” x 20’ drill pipe (2-3/8 IF) Price: $105,000
FAILING CF15 DRILL RIG, WATER TRUCK AND DRILL PIPE TRAILER (Ref#3525Tab)
FAILING CF15 DRILL RIG Manufactured 1980, 5-1/2 x 8” Gardner Denver duplex pump, 23’ kelly, chain pulldown, air clutches, breakout wrench, 5-5/8” retractable rotary table, derrick 34’ from table to crown, mounted on 2005 Kenworth T300, 3 hydraulic leveling jacks, 260’ of 2-7/8” x 20’ drill pipe, roller and drag bits, very good condition, currently drilling
1986 GMC GENERAL WATER TRUCK AND RIG TENDER 2,500 gallon Flatwater Fleet water tank, 300 gallon fuel tank, pump and hose, 2010 Kaeser M57 210 cfm air compressor (1200 hours), upper platform to carry two (2) pallets, spot lights, toolboxes, 162,000 miles
Eager Beaver 9 Ton Tri-Axle Trailer with 600' of 2-7/8 IF x 20' drill pipe, 600' of 2-3/8 x 20' extra heavy wall drill pipe, bits, subs
PACKAGE PRICE: $270,000
FAILING CF15 (Ref#8369N)
Manufactured 1974, LeRoi 50S2 air compressor, 5 x 6 mud pump, 5-1/4" retractable table, 3-3/8" fluted kelly, 3 hydraulic leveling jacks, pulldown, mechanical clutches, breakout wrench, mounted on 1974 International tandem axle truck with Detroit 8V71 diesel engine (overhauled less than 1000 hours), 200' of 2-7/8" x 20' drill pipe Price: $100,500
FAILING CF15 (Ref#5944)
Manufactured 1973, 5 x 6 mud pump, 8” rotary table, 2-3/8” kelly, mounted on 1966 Kaiser Military 5 x 5 10-wheel truck with 6 cyl diesel engine, 200’ of 2-3/8” drill pipe, truck in fair condition Price: $49,000
FAILING CF15 DRILL RIG (Ref#3058T)
Manufactured 1972, 5 x 6 Failing piston pump, Leroi air compressor with enough air to drill down to 450’ of 6” hole, Bean injection pump, spare table and swivel, 6V92 Detroit diesel, 9 speed, mounted on 1972 GMC General, new tires, 300’ of 3-1/2” (2-3/8 IF) drill rod Price: $72,500
FAILING 1250 DRILL RIG (Ref#7861T)
Manufactured 1978, 5 x 6 mud pump, Leroi 50SD air compressor, 5-1/2” retractable table, chain pulldown, mechanical clutches, mounted on 1978 Ford truck, PTO, breakout wrench, rod box, approx. 300’ of 3” x 15’ (2-3/8 IF) drill pipe Price: $62,500
FAILING 1250 HOLEMASTER (Ref#796T) Manufactured 1988, 5 x 6 Failing mud pump, (extra 5 x 6 pump included), 85 cfm Atlas Copco air compressor (can be remounted as an auxiliary compressor), 2” diaphragm mud pump, 7-1/2” retractable table, capable of drilling o 16”, mounted on 1988 International truck with DT466 (235 hp) engine, engine rebuilt 2012 with only 4000 hours), 10 speed transmission, 360’ drill pipe, tooling, 4-1/2” – 20” bits Price: $122,500
FAILING 1250 HOLEMASTER DRILL RIG (Ref#1531T) Manufactured 1980’S, freshly rebuilt 5 x 6 mud pump, retractable table, 3” hex kelly pulldown, mechanical clutches, mounted ON 2010 Peterbilt truck with diesel engine, 2 rear hydraulic leveling jacks (front jack is available but not currently on rig), pipe rack, 300’ of 3” x 16’ drill pipe, stored inside Price on Request
FAILING 1250 (Ref#6070Ra)
Manufactured 1988, PTO, mounted on 1993 Ford 9000 with 250 Cummins engine, 9 speed Fuller transmission, 5 x 6 mud pump, no air, 5-1/4" stationary table, 2" Little Giant swivel, 18' x 3 5/8" round Kelly, hydraulic pulldown, mechanical clutches, breakout tongs, 2 rear hydraulic leveling jacks, 200' drill pipe, ready to go PRICE REDUCED: $55,000
FAILING 1250 (Ref#10385Na)
Manufactured 1972, 5 x 6 mud pump, 50S1 LeRoi air compressor, pulldown, mechanical clutches, mounted on International tandem axle truck with gas engine, 40,000# mast, 15,000# drawworks, 3 drum bailer, single line pull, driller and helper's platforms, hydraulic pulldown with 1-1/2" pulldown chains, 2" Little Giant swivel, toolracks, 3 hydraulic leveling jacks, 240' of 3-1/2" x 15' FJ (2-3/8 IF) drill pipe, LF breakout wrench, good condition, currently drilling Price: $90,000 PRICE REDUCED: $87,500
FAILING 1250 (Ref#3873R)
Manufactured 1980, mounted on 1980 International truck with DT466 engine, 5 x 6 Gardner Denver mud pump, no air compressor, 5-1/4” retractable rotary table, 3-1/2 X 24’ kelly, chain pulldown, 2” swivel, new fuel pump, new head gasket PRICE REDUCED: $49,500
FAILING 1250 (Ref#1734N)
Manufactured 1978, PTO, mounted on Ford with diesel engine, 5 x 6 mud pump, 500/200 on board air compressor, 6” retractable table, chain pulldown, mechanical clutches, breakout wrench, 1 front & 2 rear hydraulic leveling jacks, 200’ of 3” x 20’ drill pipe Price: $57,500
FAILING 1250 (Ref#1735N)
Manufactured 1982, PTO, mounted on International with diesel engine, 5 x 6 mud pump, 250/200 on board air compressor, retractable table, chain pulldown, air clutches, breakout wrench, 1 front & 2 rear hydraulic leveling jacks, 2 7/8” x 20’ drill pipe Price: $46,500
FAILING 1250 (Ref#12693T) Manufactured 1973, 5 x 6 mud pump, chain pulldown, retractable table, mounted on 1973 International truck, 345 gas engine, no drill pipe Price: $54,500
FAILING CFD2 DRILL RIG (Ref#8107T)
Built 1964, 4-1/2 x 5 Failing mud pump, Grimmer Schmidt 125cfm developmental air compressor, 5-1/4” stationary table, 2-3/8” kelly, 10' stroke, mounted on 1984 International truck with DT466 engine, PTO), 4 hydraulic over mechanical jacks, needs new tires
340’ of May Jr Rods
340’ N rods
Has not run in since 2016
Package Price: $62,500
FAILING CFD-1B (Ref#14819T)
Manufactured 1965, mounted on 1979 International S series 2551 tandem axle truck with DT466 diesel engine, (2) mud pumps: Failing FM45 5 x 6 duplex and Gardner Denver FG FXG 5 x 6 duplex, Ingersoll Rand Type 30 250/125 air compressor hydraulically driven, 26’ x 25,000# derrick, 3-3/8” x 18’ kelly, King 15 KF water swivel, 1-1/4” pulldown chains, 5-1/4” rotary table with locking nut, air controlled clutches, welder, pipe rack, 150 gal mud pit, breakout tongs, 1 front & 2 rear hydraulic leveling jacks, stored inside, sitting but running when parked Price: $35,000
FAILING CFD-1 (Ref#1957N)
5 x 6 Wheatley mud pump, Gardner Denver developmental air, hydraulic pulldown, mechanical clutches, stabilizer, mud pan, 3-1/2" kelly, stationary table, mounted on Ford Louisville tandem axle truck with 290 Cummins engine, PTO, 2 rear hydraulic jacks, 200' of 3-1/2" x 20' drill pipe, good condition, currently drilling Price: $65,000 PRICE REDUCED: $50,000
FAILING CFD-1B DRILL RIG (Ref#9974T)
7-1/2” rotary table stationary, 5-1/2 x 6 Failing mud pump with new sleeves and pistons, mounted on 1993 Ford L8000 Tandem axle truck with diesel engine, PTO, 20’ stabilizer, bits, subs, tools, sliding rod box, 300’ of 3-1/2” x 20’ drill pipe (like new) Price: $137,500
FAILING 1000 (Ref#319N)
3 x 4 Gardner Denver mud pump, 650/50 compressor, PTO, mounted on 1979 International 2-ton tandem axle truck with diesel engine, 3-1/2” kelly, 7-1/2” fixed table, 3 hydraulic jacks, pipe rack, mechanical pulldown, 300’ of 2-7/8” drill pipe (2-3/8 IF) PRICE: $52,500
FAILING HOLEMASTER 1000 (Ref#2616T)
Mounted on 1974 Mack truck with V8 Mack engine, new 2" Little Giant swivel, 23' kelly, 5-1/4" rotary table, 256 LeRoi air compressor, 5 x 6 Gardner Denver piston pump, 2 hyd jacks, low hours, ready to work PRICE REDUCED: $72,500
FAILING CFD-2 (Ref#3011R)
Mounted on 1996 Ford F series 2 wheel drive with 5.9 Cummins diesel engine, 5-1/4" stationary table, 2 3/8" x 15' Kelly, 5x6 GD mud pump, chain pulldown, mechanical clutches, breakout wrench, rod rack, 255' of 15' Mayhew Jr rods, subs, bits, casing elevators, 4 hydraulic leveling jacks, ready to go
PRICE REDUCED: $52,500
FAILING 750 HOLEMASTER (Ref#894T)
4-1/2 x 6 Gardner Denver piston mud pump, no air, 2-7/8" x 18' kelly (runs 10' x 2-708" rods), mounted on 2000 International 4700 w/DT466 engine, no drill rod, Mayhew Junior thread on kelly, all new hydraulic control valves, brakes clutches are all new or have recently been replaced Price: $37,500
FAILING 250 DRILL RIG (Ref#2821T)
Manufactured 1985, mounted on Ford F800 4 x 4 truck with diesel engine, front winch, rotary table, drawworks and mud pump are new, set up for 4” wells, drill pipe and tools included Price: $49,500
FAILING 250 (Ref#3448T) Manufactured early 1970's, mounted on Ford 6 wheel drive Ford F750 truck, 391 gas engine, 4-1/2 x 5 mud pump, 290 cfm air compressor, 4" retractable table (no casing can go through), chain pulldown, 2-3/8 kelly, sandline, 10' stroke (can be pulled to 20'), running condition Price: $29,500
MUD ROTARY RIG (similar to Mayhew) (Ref#9761T)
Built 1950’s, 5” table, 3 x 6 Wheatley 2-piston mud pump (with 2 new spare liners and 2 new spare pistons), approx. 15’ kelly, mechanical rig, well maintained, mounted on 1999 International 4700 w/DT 466E 6 cylinder engine, PTO, runs 10’ drill rod Price: $31,500
MIDWAY 15M (Ref#7588R)
Manufactured 1980, Midway 1500 drawworks, PTO, mounted on 1980 International f-2574 with 1996 Detroit engine, 10 sp transmission, 38000# rear axles, 24.5 bud wheels, 16000# front axle w/22.5 floatation tires, 4 leveling jacks, 5 ½ x 8 mud pump, new 8-1/2" Midway retractable table, 3-3/4" x 34' fluted kelly (new 2011), 3-3/4" x 5-1/4" new master bushing, 49'2" mast with new cylinders (can run 44'5" casing), 3" plumbing, 2" swivel, 2" kelly hose, hydraulic pulldown, new drivemotor 2013, hydraulic cathead, 792 Spicer transfer case (rebuilt 2013 with air controls), new lifting cylindes on mast, new main hyd pump 2012, 4 part linesm BVM breakout tong, heavy duty work floor with hinged trap door
1600' of Range II pipe (2-7/8 IF) with trailer, doghouse, drill collars, 1991 International winch truck, 1995 International bus doghouse, tools, subs, welder, torch and spare parts
Package Price: $258,500
MIDWAY 15M DRILL RIG AND WATER TRUCK (Ref#6505T) Mounted on 1991 Kenworth truck, 54’ mast, 5-1/2” x 8” mud pump, 500/250 air compressor, 8-1/2” retractable table, spinning chains, 4 hyd jacks, 2-1/2” Little Giant swivel
1981 Kenworth Water Truck, 4500 gal stanless steel tank, 3 axle
PACKAGE PRICE: $375,000
MIDWAY 15M (Ref#9252Ra)
Manufactured 1975, drawworks completely rebuilt, 7-1/2 x 10 Gardner Denver mud pump, hydraulic pulldown, 54' derrick with racking board, rod box, mounted on 1978 International Paystar 5000 truck with 350 Cummins engine. Price: $139,500
MIDWAY 1500 DRILL RIG (Ref#2891T)
Manufactured 1975, 600 cfm/150 air compressor, mounted on 1975 Autocar with 350 Cummins engine, new tires, misc tools, bits, Gardner Denver 5 x 6 mud pump, 400' drill pipe Package Price: $62,500
MIDWAY 1500 (Ref#15626R) Manufactured late 1970’s, no mud pump, square kelly, no pulldown, 8” retractable table, mounted on newer Freightliner truck with diesel engine, air clutches, no pulldown, breakout tongs, 1 front and 2 rear hydraulic leveling jacks, no rod box, no pipe rack, 300’ of 20’ drill pipe (2-3/8” IF), Price: $54,500
MIDWAY 1300 (Ref#3054N) Manufactured 1980, one owner/operator, 5 x 6 mud pump, 100 SDS LeRoi air compressor, mounted on 1980 Ford LT9000 tandem axle truck with 6V71 Detroit engine, 8-1/2" retractable table, 4" x 25' kelly, mechanical clutches, pulldown, 2 rear hydraulic leveling jacks, 400' of 2-7/8" x 20' pipe, some tools PRICE: $97,500
MIDWAY 13M (Ref#14795T)
Manufactured 1978, PTO, mounted on 1979 Ford 9000 with Cat engine, 5x6 mud pump, Leroi 750cfm air compressor, 3" x 23' kelly, 8" stationary table, breakout wrench, rod box, hydraulic pulldown, mechanical clutches, mud pan, 300' of 2 7/8" x 20' drill pipe, no leveling jacks, good running condition
Price: $80,000 PRICE REDUCED: $54,500
MIDWAY 1250 (Ref#12353R)
PTO, mounted on 1991 Mack with diesel engine, 5x6 mud pump, GD air compressor, 7-1/2" stationary table, pulldown, manual clutches, rod rack, 2 hydraulic leveling jacks, good condition Price: $67,500
FRANKS 55 (Ref#1849N)
32’ square kelly, 51’ mast for Range III casing, mounted on GMC truck, propane engine on deck and in carrier, 8” retractable table, air clutches Price: $87,500
PORTADRILL TKT PROSPECTOR (Ref#8281N)
Manufactured 1978, Triple drum, new bearings on drawworks and pulldowns, 5-1/2" x 8" Gardner Denver duplex mud pump, no air compressor, 57' x 60,000# hydraulic raised mast, Racking board, Mounted on 1978 Kenworth tandem axle truck with 8V92 Detroit diesel and PTO, 4 hydraulic leveling jacks and 2 rear screw jacks, Hydrostatic drive drawworks and rotary table, water injection, 8-1/2" retractable rotary table (4 speed transmission on rotary table), will run Range 3, 4-1/2" x 25' kelly, 4 speed hyd pulldown
Price: $95,000
Also available at extra cost:
2000' of 3-1/2" x 20' drill pipe and additional rebuilt compressor
500' of 4-1/2" flush joint pipe
3" kelly
PORTADRILL TKT MUD ROTARY RIG (Ref#8015Tb)
Manufactured 1984, Leroi 600/250 air compressor, 5-1/2 x 8 duplex mud pump, 53’ tubular mast, racking bord, hydrostatic double drum drawworks, 7-1/2" hydrostatic rotary table, hydraulic pulldown, 24’ kelly bar, 3000’ capacity sandline, mounted on 1982 Kenworth C500 truck with 6V92TAC Detroit diesel, breakout tongs, hydraulic breakout wrench, hydraulic cathead with spinning chain, pipe rack, 1 front and 2 rear hydraulic jacks, 2-7/8" upset x 20’ pipe, 4-1/2" flush joint x 20’ pipe Price: $194,500
PORTADRILL TKT PROSPECTOR (Ref#8281N)
Manufactured 1978, Triple drum, new bearings on drawworks and pulldowns, 5-1/2" x 8" Gardner Denver duplex mud pump, no air compressor, 57' x 60,000# hydraulic raised mast, Racking board, Mounted on 1978 Kenworth tandem axle truck with 8V92 Detroit diesel and PTO, 4 hydraulic leveling jacks and 2 rear screw jacks, Hydrostatic drive drawworks and rotary table, water injection, 8-1/2" retractable rotary table (4 speed transmission on rotary table), will run Range 3, 4-1/2" x 25' kelly, 4 speed hyd pulldown
Price: $95,000
PORTADRILL TKT (Ref#417N)
Manufactured 1976, PTO, mounted on International Paystar 5000 with rebuilt 350 Cummins engine, 6 x 8 Gardner Denver mud pump, 256S2 Leroi compressor, Bean water injection, 7-1/2" retractable table, 53' hydraulically raised mast, hydraulic pulldown, hydrostatic, breakout tongs, 4-1/2" hex Kelly (fluted available) no pipe rack or rod box
Price: $245,000 PRICE REDUCED: $179,500
Pipe available at extra cost
PORTADRILL 10 TKT (Ref#1236T)
Manufactured 1974, 5-1/2 x 8 Gardner Denver chain driven mud pump (rebuilt), 256 LeRoi air compressor (rebuilt), 7-1/2” retractable table, mechanical clutches, pulldown, 4-1/2” x 23’ kelly (mast is set up for 30’ kelly), mounted on 1999 Kenworth truck with 440 hp Cat engine, PTO, pipe spinner, breakout tongs, water injection pump, 3 hydraluc leveling jacks, good condition, rebuilt hydrostate, chain cases and rotary table, 200’ drill pipe and tools Price: $265,000
PORTADRILL TKS DRILL RIG (Ref#6628T)
Manufactured 1978, Leroi developmental air compressor, 3 x 4 centrifugal pump, Detroit 12V diesel deck engine, 21’6” kelly, mounted on White Road Boss tandem axle truck with 8V Detroit diesel, rod box, no carousel, 300’ of 3-1/2” x 15’ and 20’ drill pipe, sitting since 2019 Price on Request
PORTADRILL 10TK (Ref#1662R)
Manufactured 1974, PTO, mounted on 1974 Diamond Rio with Detroit 8V92 Detroit engine (3 years old), extended mast, rebuilt drawworks & Leroi 256S2 air compressor, no mud, sandline, 4-1/2" x 23' Kelly, breakout tongs, 8" retractable table, air clutches, hydraulic pulldown, pipe rack, 1 front & 2 rear hydraulic leveling jacks, 200' of 4-1/2" x 15" drill pipe, rig in operating condition Price: $100,000 PRICE REDUCED: $79,500
PORTADRILL 10TK (Ref#1769T)
Manufactured 1976, 3 x 4 centrifugal mud pump, LeRi 256S2 air compressor (very low hours on rebuilt), Detroit 8V92 deck engine, mounted on 1976 Paystar 5000 truck with International diesel engine, 3 hyd leveling jacks, 8-1/2" retractable table, 4-1/2" fluted kelly, new swivel, racking board, 38' mast, BJ tongs, air hammer, spare TKT transmission, some tools,
800' of 4-1/2" x 15' pipe
1978 INTERNATIONAL PAYSTAR 22' flat tank, 2200 gallon, 400 Cummins
Package Price: $100,000
PORTADRILL 10TK RIG PACKAGE (Ref#7493T)
PORTADRILL 10TK Manufactured 1979, 2 drum drawworks plus sandline, Gardner Denver 6 x 8 mud pump, 256 LeRoi air compressor, 8-1/2" retractable table (can run 16" casing through table opening), 32' fluted kelly, extended 60' mast, 32' kelly, pull down chain on a 4-speed transmission, racking board holds over 3000' of 40' stands, spinning chain, mounted on 1979 International Paystar 5000 truck with Detroit Silver 92 engine, PTO, 13 speed transmission, 3 hyd leveling jacks (also comes with mounting beam to install two more jacks across belly of mud pump and a fold up work floor on back of rig). Well maintained
1400' of 2-7/8" x 20' pipe (2-3/8 IF)
400' of 4" x 20' pipe (2-7/8 IF)
Collars, bits, elevators, etc.
1997 Kenworth T80 water truck, 4000 gallon tank, M14 Cummins, 10 speed transmission, 6 spray nozzles
1980 Ford 9000 service truck, tandem axle, Detroit straight 6 engine, pipe racks, toolboxes
Package Price: $720,000
PORTADRILL 12TK DRILL RIG (Ref#3369Ta)
Manufactured 1972, Detroit 318 engine, 7-1/2” retractable table, 4” x 36’ kelly, chain pulldown, mounted on International 4900 tandem axle truck with 466 DT engine, 10 speed transmission, 400’ of 4-1/2” x 20’ (3-1/2 IF) drill pipe, 700’ of 4” x 30’ FH drill pipe, handling tools, last used 2021, 4 x 3 centrifugal MCM pump with John Deere engine Price: $93,500
PORTADRILL 10TK (Ref#14681Na)
Manufactured 1972, Atlas Copco 586/125 Model DR4 air compressor, 6V71 Detroit diesel on deck, Mission 3 x 4 mud pump, hydrostatic drawworks, 15 gpm Bean water injection pump, line oiler, 42’ mast with rack for pulling double 15’ stem, 4-1/2” kelly, 8” retractable table, 60,000# pullback, 60,000# hoist capacity, 5,000# winch cap, mounted on 1972 International tandem axle truck with DV550 (200 hp) diesel engine, one owner rig, well maintained, bare rig Price: $95,000
PORTADRILL 524 DRILL RIG (Ref#374T)
PORTADRILL 524 DRILL RIG (Ref#7762Ta) Gardner Denver 5 x 6 mud pump, 250/120 developmental air compressor, 3 cylinder Bean pump, 7-1/2” retractable table, mounted on 1993 International truck Model 9400 with Cummins N14 (350 hp) engine, PTO, 4 leveling jacks, rod box, 400’ of 2-7/8” x 20’ drill pipe, wrenches, tools, currently working Price: $105,000
PORTADRILL 524-3A DRILL RIG (Ref#3045T)
PORTADRILL 524 (Ref#2592R)
Manufactured 1979, mounted on 1979 International Paystar 5000 truck, 5 leveling jacks, 7-1/2” retractable rotary table, 26’ kelly, 2” Little Giant swivel, 5-1/2 x 8” Gardner Denver mud pump, 256 LeRoi air compressor, racking board Price: $112,500
WINTER WEISS/PORTADRILL 500 AND WATER TRUCK (Ref#6890T)
Rig built 1952, trailer mounted, 2 drums, andline, 5 x 6 duplex mud pump, pull down, rotary table, 5” Kelly, 6 cylinder 250 gas engine, hydraulic leveling jacks on front, mechanical leveling jacks on rear, 400’ of 2-7/8” x 15’ drill pipe.
Rig is pulled by 1977 International water truck with 1850 gallon tank powered by 318 diesel engine.
Last drilled 2020
Package Price: $47,500
PORTADRILL 522 DRIL RIG (Ref#3959Ta) Mounted on 1975 International with DT466 engine (engine needs work), 5-1/2 x 8 Gardner Denver 200-FXX-001 mud pump, not used since 2016
PORTADRILL 524 DRILL RIG (Ref#3959Tb) kelly, missing rotary table, no leveling jacks Mounted on International truck, ex-government rig
PRICE FOR BOTH RIGS: $55,000
PORTADRILL 120 (Ref#9801T) Manufactured 1968, 5 x 6 Gardner Denver mud pump, 6" stationary table, 3-1/2" x 23' kelly, mounted on 1987 Peterbilt with diesel engine, PTO, pipe rack
1989 Kenworth Water Truck, diesel engine, 9 sp transmission, 2500 gallon plastic tank
Dual axle trailer with Ford backhoe
Wheatley 6 x 6 mud pump (no engine)
Many spares
200' of 2-3/8" x 20' pipe
Package Price: $95,000
SHOP BUILT TRACK MOUNTED AUGER/MUD ROTARY DRILL RIG (Ref#619Tc)
Manufactured 2015, Kubota engine with 210 hours, track drill, no hammer, can auger or mud rotary with external pump or there is a place for pump to be installed, like new Price: $52,500
BADGER 1250 DRILL RIG (Ref#7957T)
5 x 6 mud pump, air compressor, kelly mounted on Ford truck with Cat engine - Price on Request
SHOP BUILT MUD ROTARY RIG (Ref#4668T)
Built 1986, approx 540’ depth, double drum (shop build with triple clutch on each side), Gardner Denver 5 x 8 mud pump, 2” DSM swivel, 8-1/2” retractable table, trailer mounted, 46’ mast mechanically raised, 4” square kelly, 420' of 2-7/8" drill pipe Price: $47,500
INGERSOLL RAND RO-300 DRILL RIGS (Ref#1555Ta)
Detroit V8 engine, 11 speed transmission, 5 x 10 Gaso hydraulic mud pump, 42’ mast, 8-1/2” retractable table, 4-1/2” x 25’ fluted round kelly, hydraulic drive winch, mounted on 1980 International, 4 hyd jacks Price: $122,500
DAVEY DRILL RIG (Ref#9591T)
Manufactured 1986, air compressor, Detroit deck engine, 21’ kelly (a 30’ kelly is available), stationary rotary table (3 extra tables available), mounted on 6x6 International all wheel drive with Detroit engine, rod box, 3 hydraulic leveling jacks, 400’ of 4” x 20’ drill pipe, 3 drill bits, incudes 3 spare jacks and 4 spare Davey air compressors Price: $97,500
DAVEY M8W KELLY AIR RIG (Ref#2884Na)
Manufactured 1976, mounted on Louisville Ford truck with 54 gas Ford engine, 5 and 4 transmission, new clutch, 38,000# rear, 26-1/2' Kelly bar 4" round, King swivel, 35' tower, 7-1/2" sliding table, 671 Detroit diesel deck engine, 500 cfm/125 psi Davey air compressor rebuilt with less than 2000 hours, water injection system hydraulically operated, 100' of 4" x 20' flush wall drill pipe, can drill to 900', can hold 300' steel
PRICE: $35,000
DAVEY M8 KELLY AIR RIG (Ref#2884Nd)
Manufactured 1975, mounted on tandem axle Ford Louiville truck with 534 gas engine, 5 x 4 transmission, leveling jacks, 38,000# rear, good tires, 671 Detroit diesel engine, 500 cfm/125 psi Davey air compressor, rod box, 7-1/2” fixed table, 32-1/2’ x 4-1/2” Kelly bar, runs 4” drill string, 46’ one piece mast (can be reduced), work platform, holds 300’ drill pipe, 300’ of 4” x 20’ drill pipe, slips, 8-3/4” bit, 5-7/8” sub PRICE: $35,000
DAVEY (Ref#10682T)
500/125 Davey air compressor, 7-1/2” fixed table, 32-1/2 x 4-1/2” kelly bar, 46’ one piece mast (can be reduced), 671 Detroit deck engine with 5 x 4 transmission, mounted on 1978 Ford 900 tandem axle truck with 534 gas engine, leveling jacks, 38,000# rear, rod box (holds 300’ of pipe), slips, work platform, 200’ of 2-7/8” drill pipe, runs 4” drill pipe PRICE: $37,500
SHOP BUILT MUD ROTARY DRILLING RIG (Ref#7785T)
Built approx 2007, 150’ – 200’ depth capacity, rig has heavy duty railroad winch cable for up and down drilling operations or for pulling pumps, 3” centrifugal mud pump, IR 40 cfm developmental air compressor, pump and compressor run off Handona gas engines, boom will handle 10’ or 20’ rods, mounted on 1998 Ford 700 2 wheel drive truck, 7 ltr propane engine, (2) tanks (40 and 80 gal), drilling, hydraulics and truck run on propane, 500 gal water tank, pipe rack, compact rig. Includes approx 120’ of 1-1/4” x 10’ rods, bits for 1-1/4”, 2” and 4” wells, Price: $30,000
BUCYRUS ERIE 10R (Ref#5558Ta)
Manufactured 1974, mounted on 1974 Ford LN8000 with rebuilt Cat 3208, new front tires, no ruse, LeRoi compressor, 5 x 6 Gardner Denver mud pump, injection pump, new 2” plumbing, 8” retractable table, 3 hyd jacks, rod rack, 5 stabilizers 6”-12”, 19 rods of 2-7/8”, 26 rods of 3-1/2”, several bits and subs 4”-10”
2005 FREIGHTLINER WATER TRUCK (Ref#5558Tb)
1000 gal water tank, C7 engine, tandem axle, 18,000# boom with 60’ reach, 250 Miller welder and generator, grouter, 18’ rack, toolboxes, air brake trailer package, hitch
Package Price: $167,500 CDN
BUCYRUS ERIE 10R (Ref#11705T)
Manufactured 1973, 5 x 6 Gardner Denver mud pump (new pistons and liners 2016), 50 SDS air compressor, bailing drum, 24’ kelly, 8-1/4” retractable table, hydraulic pulldown, air clutches, mounted on 1989 Chevy Topkick with Cat 3208T, rod box, 300’ of 3” drill stem, tools, well maintained Price: $47,500 Additional pipe available at extra cost.
EWBANKS 51 DRILL RIG (Ref#1427Tb)
EWBANKS 50 (Ref#13911Ra) 4 x 5 mud pump, mounted on 1978 International single axle truck, Cat 3208 engine, PTO, 5-1/4” stationary rotary table, no air, square kelly, mud pan, pipe rack, 200’ pipe Price: $37,500
MOBILE B40-L12 (Ref#5066T)
Built 1986, mounted on 1986 GMC Brigadier truck with Cat 3208 engine, Ford 4 cylinder Industrial deck engine, 5 x 6 mud pump, 1 mainline winch, 1 sandline winch with free fall, sitting outside for a while, was in proper working condition when parked Price on Request
CYCLONE T10 DRILL RIG (Ref#10916T)
Gardner Denver 5 x 6 mud pump, 12” kelly and a smaller diameter kelly, 3’ table, 30’ mast, single drum, mounted on 1977 International 1850 truck with Cat 3208 engine, PTO, 13 speed Fuller transmission, leveling jacks, (10) 4-1/2” x 21’ drill pipe, used for large diameter and small diameter wells for irrigation, manual/parts book, not used for several years Price: $65,000
CYCLONE 300 DRILL RIG (Ref#373T)
Manufactured 1973, 871 Detroit diesel on deck, 450 cfm Bendix Westinghouse air compressor, no mud pumps but hydraulics are there, 4” kelly, 8” retractable table, bailing line, mounted on 1972 Ford F900 tandem axle truck with 434 gas engine, 3 hydraulic jacks, 200’ of 4-1/2” x 15’ drill pipe, sitting since 2019 Price: $37,500
SANDERSON CYCLONE 36R COMBINATION ROTARY/SPUDDER RIG (Ref#11403Tb)
4 cylinder Ford diesel engine on deck, 38' hydraulically raised mast, 5-1/2" table retractable to 18" x 12" deep, 3-1/2" x 20' fluted Kelly, drill line drum, sandline drum and casing drum (no line on rig). 2-part block, shock in the crown for cable drilling, Mounted on 1992 Ford L7000 all-wheel drive truck with 6 cyl Ford diesel engine, automatic transmission with big hydraulic pump, low miles, 3 hydraulic leveling jacks, needs new hoses and swivel. Price: $32,500 - Oklahoma
CYCLONE 35R (Ref#6558T) 5” Gardner Denver mud pump with 3 cyl diesel engine, no air, square kelly, retractable table, hydraulic pulldown, pipe rack, 4 cylinder diesel deck engine, mounted on 1985 Mack twin screw with diesel engine, 3 hyd leveling jacks, 300’ of 2” x 16’ drill pipe Price: $64,500
CYCLONE 35R COMBINATION MUD ROTARY CABLE TOOL RIG (Ref#10514T)
Built 1966, 5 x 6 mud pump, developmental air compressor, mounted on 1966 Ford F950 Super Duty with gas engine, (2) gas deck engines (one runs rig, one runs air compressor and mud pump), 240’ drill rod, 15’ sub and bit Price: $29,500
SUN 500’ DRILL RIG – NEW MANUFACTURE (Ref#12607T)
Built new 74 HP Kohler Tier 4 Turbo diesel industrial deck engine, Industrial Permco dual 28 gpm main pump w/vari speed split driver circuits in volve controls, 3 x 2” MCM Model 118 mud pump 350 gpm/95 psi, 150 rpm main drill head 1000 ft/lb torque, 55 gal hyd reservoir, 12,000# push/pull force w/chain hoist drive, 16’6” tubular 4x6 mast 12’ stroke, designed for 10’ Mayhew Jr drill pipe, 82000 BTU hydraulic oil cooler, swivel with extreme duty 18,000# twin thrust bearing set and shevron seals w/changeable ware sleeves, hydraulicuniversal breakout system, swing away drill head, ½” minimum watercourse through all piping, 22 gallon fuel tank, 20’ of 3” charge line, 20’ of 2” bypass hose w/cam locks, 12 volt primer and wash down pump, removable drill pipe guide, 1200# hydraulic accessory host telewscoping to 22’ height for casing work w/drill pipe tool for lifting and handling drill stem. Weight (skid mounted unit): 6500 lbs., dimensions (trailer mounted) 110” long x 90” wide (will fit in 20’ shipping container) Price, skid mounted: $59,500 Price, trailer mounted: $69,500
For Additional Information, Call, Email or Fax Maryann