Last Updated: 04/26/2024 1:02 PM
AUGER SPECIALS
FOR ADDITIONAL INFORMATION AND PHOTOS CONTACT MARYANN AT (516) 536 7375 OR EMAIL rigs@sunmachinery.com
FOR DIRECT PUSH MACHINES - CLICK HERE
DEEPROCK DR150 AUGER DRILL RIG (Ref#1685Ta)
Mounted on 1993 Ford F700 truck, PTO, 3 winches, slide base, auger rack, toolboxes Price: $42,500
DIEDRICH D-120 (Ref#11401T)
Manufactured 2014, mounted on Morooka 1500 with diesel engine, John Deere 4 cyl diesel deck engine, Moyno 3L8 pump, auto hammer, 2000#, 5000# and 10,000# winches, wireline winches, breakout wrench, rod holder, no cathead, no angle capability Price: $239,500
DIEDRICH D120 AUGER DRILL (Ref#2361Tb)
Manufactured 2009, Deutz engine (approx. 8500 hours), Moyno 3L8 pump, 800 lb winch, 1000 lb winch, 10,000 lb winch, Mobile Safe-T driver winch and drop hammer, 140 lb auto hammer, mounted on 2009 International 4400 SBA 6x4 truck, Eaton Fuller transmission, 190,533 miles, well maintained Price: $170,000
DIEDRICH D120 DRILL RIG (Ref#9651T)
Mounted on 2001 Marooka, new pump and tools Price: $184,500
DIEDRICH D-120 (Ref#6597N)
Manufactured 1996, John Deere 6 cylinder diesel deck engine, mounted on 1995 Freightliner with Detroit 12.7 liter engine, flotation tires in front, in-out and side to side slide base, breakout table, breakout wrench, 500 gallon water tank, 140# SPT hammer, cathead, (2) 3000# winches, 10000# winch, set up for mud, rotary or augers, 2 swing out auger racks, 4 leveling jacks Price: $67,500
DIEDRICH D-120 (Ref#4890Na)
Manufactured 1991, rebuilt John Deere deck engine (359 hours), mounted on 1996 Freightliner FLD120 with Cummins N14 engine, 10 speed transmission, rebuilt Moyno 3L8 pump, 500 gallon water tank, cathead, fluted kelly Price: $140,000 PRICE REDUCED: $112,500
DIEDRICH D120 (Ref#4889T)
Manufactured 1991, John Deere inline 6 diesel engine, low hours, 3L8 Moyno, 500 gal tank, cathead, fluted Kelly, 2 auger racks, toolboxes, 4 outriggers, 3 winches (3k, 7k, 10k), mounted on 2001 Sterlilng AT9513 truck, 10 speed, approx. 578,000 miles Price: $140,000 PRICE REDUCED: $112,500
DIEDRICH D90 AUGER DRILL RIG (Ref#772T)
Manufactured 2008, mounted on 2008 Morooka TCX 850 Price: $215,000
DIEDRICH D50 AUGER DRILL (Ref#7211T)
Manufactured 2018, approx. 5000 hours, John Deere 4 cylinder Turbo diesel 4.5L Powertech Tier 3 engine, 3L6 Moyno pump, 250 gal steel water tank, 3 hydraulic hoists 7000#, 2000#, WL800#, tramming winch, auto hammer, no cathead, rear auger rack, custom rod racks (5’ and 10’), 2 remote controls, slide base in/out, wiggle tail, breakout wrench, King water swivel, hydraulic rod table/clamp, drop down side work table, driller’s platform, flip down sheave block for lower tramming/travel clearance, SPT auto hammer calibration certification Price: $275,000
DIEDRICH D50 DRILL RIG (Ref#242T)
Manufactured 2016, track mounted, John Deere 4 cylinder turbo (115 hp) diesel engine, 24” wide rubber 2-speed track, tandem hydrostatic drive pump, in/out and side to side slide base, cathead, front carrier winch, FMC LO6HV water pump, hydraulic rod holder, breakout wrench, right angle drive, 2-speed all rear drive rotary box, Automatic 140 lb SPT hammer, front auger rack, side tooling rack, 4 hyd jacks, main winch, sandline winch, sampling winch Price: $265,000
DIEDRICH D50 AUGER DRILL (Ref#2361Tc)
DIEDRICH D50 DRILL RIG (Ref#5473T) Manufactured 2013, diesel deck engine, probe hammer, mounted on International truck with diesel engine Price: $137,500
DIEDRICH D50 (Ref#4549T)
Deutz 4 cylinder diesel on deck, mounted on all wheel drive 1995 International 4800 truck with diesel engine, no auto hammer but plumbing is there, starts, needs rebuilding Price: $23,500
DIEDRICH D50 TRACK MOUNTED AUGER DRILL (Ref#8726Ta)
Price: $110,000 CDN
DIEDRICH D50 DRILL RIG (Ref#3452Tb)
Manufactured 1990’s, auto hammer, 3 winches, 6 cylinder John Deere diesel engine, mounted on 2013 Hino 268 truck, automatic, approx. 200k miles, used for hollow stem auger and mud rotary wells Price: $62,500
DIEDRICH D50 (Ref#14444T)
Early 1980’s, Duetz diesel on deck, mounted on 2002 International 2 wheel drive truck with diesel engine, angle capability, no auto hammer, cathead, water tank, Moyno pump, in/out and side to side slide base, 3 leveling jacks Price: $95,000 PRICE REDUCED: $92,500
DIEDRICH D50 AUGER DRILL (Ref#4133T)
Manufactured 1995, 19’ mast, 5,000 and 2000 lb winches, auto hammer, breakout wrench, water tank, 4 cylinder John Deere diesel deck engine, mounted on 2006 Peterbilt 335 truck with Cummins engine, Eaton 10 speed transmission, 96,000 miles, A/C, 85% tires, 3 leveling jacks, rig in good shape, bed is rough Price: $92,500
DIEDRICH D50 (Ref#8817T) Manufactured 1987, 4 cyl gas engine on deck, slide base, cathead, unmounted (frame only) was originally skid mounted Price: $23,000
Manufactured 2015, skid-mount rig mounted on a D&B/Nomanco ST7512 tandem-axle trailer (10,000 # GVWR) with hydraulic jacks, 3L4 Moyno pump, 27 HP Kohler gas engine, 15-foot mast, 2000# hoist 2 speed with brake, 600 hours on engine, NPK-GH06 probe hammer (top mount), 140-pound automatic hammer, caster assembly, auger rack.
Mounted on trailer, upper spindle adaptor, lower spindle adaptor, customized with pockets for use with a forklift, stored indoors, two 5,400# Dexter axles, ST225/75R 15 Load Range E tires, LED lights, 7-way
plug, break away kit, spare tire
Price: $119,500
DIEDRICH D25 DRILL RIG PACKAGE (Ref#8097T)
Manufactured 2014, track mounted. Lombardini diesel engine. Auto hammer, Moyno 3L6 pump, main winch, front and side auger racks, tool box, rotary hoses, 4 hydraulic jacks, cathead, two mudtanks. extensive tooling including 2-1/4” HAS, JWJ rod, 3-1/4” HAS, NW drill rod, 5-1/2” auger, NWL BW, HW rod and casing and more (list available) Package Price: $170,500
DIEDRICH D25 (Ref#8857R)
Manufactured 2007, brand new Deutz air cooled 4 cylinder diesel deck engine with 500 hours, new clutch, brand new auto hammer, single winch, Moyno pump, 150 gal water tank, mounted on new 2022 Dodge Ram 5500 4 x 4 truck with Cummins diesel engine, 20 miles on truck, new hoses, new bed, no tooling, has drilled 20 – 30’ through ashphalt 50’ through sand PRICE: $118,500
GUS PECH GP1300 BRAT SERIES AUGER DRILL RIG (Ref#5760T)
Manufactured 2003, one owner rig, 13,000 ft/lb torque, 18.400 lbs pulldown, 24,500 lbs pullback, mounted on 2003 Sterling 6 x 4 truck with Cat engine, PTO, rig has 18,200 hours, 5300 hours on new engine (engine replaced at 12,900 hrs) Price: $112,500 USD
GTECH GT-8 MAX GEOTECHNICAL AUGER/CORING/MUD/AIR ROTARY TRACK MOUNTED DRILL RIG (Ref#407T)
Manufactured 2022 (delivered Jan 2023), approximately 1100 hours, Centerline Mono mud pump, plumbed for external air compressor), 44,000 LBS push and pull capacity, 16” head sliding clearance, 10” front/rear slide mast, 1970’ NWL core capacity, located Canada Price: $625,000 CDN
SCHRAMM T300E AUGER/CORE/ROTARY DRILL RIG (Ref#5656Ta)
Manufactured 2009, top head has two spindles, one for auger or rotary drilling, second with side inlet w/2 speed motor for coring, max diameter 12”, max head clearance 15’10”, mounted on 2009 International truck with Cummins diesel engine, PTO, (no hour meter, runs off miles on truck) 57,600 miles Price: $193,500
Available at extra cost:
1995 INGERSOLL RAND XHP750 SCAT AIR COMPRESSOR (Ref##5656Tb) Screw compressor with Cat diesel 300 hp engine, good running condition
CANTERRA CT-250 DRILL RIG (Ref#5926T)
Manufactured 1997, Refurbished 2009, Air/Auger/Mud Drilling), Cummins 4BT diesel deck engine (approx. 4,250 hours), 3 winches,, JIB, sandline, 2 speed power head, Moyno pump, 3 auger side racks and pipe rack, mounted on International truck powered by Cat diesel engine, 9 speed transmission, approx. 66,100 miles, 4 hydraulic leveling jacks, located Middle East Price: $62,500 USD
CANTERRA CT-250 (ref#12782T)
Mounted on AWD International 4900, single rod loader, pipe spinner, 3 hoists, cathead, 4 x 3 Mission Sandmaster, 3L6 Moyno, desander, 3.9 – 125 hp Cummins deck engine, 300 gal SS pan, 200/150 air compressor, reworked hydraulic system at a cost of $35k Summer 2020 Price: $162,500
CANTERRA CT-150 (Ref#4885Tg)
Manufactured 1989, 4 cylinder Cummins diesel on deck, 932 hours, 5.5’ stroke that splits for low clearance, adapter available to make rig with 11’ stroke, 15’ mast, cathead, centrifugal mud pump, 6000# winch, 8,000# winch, 12,000# winch, breakout wrench, rod table, auger guides (4-1/4 and 6-1/4”, high speed head for coring, mounted on 1988 Ford F700 truck, trailer Price: $37,500
ACKER SOIL MAX AUGER RIG (Ref#6027T) Manufactured 1990, 20’ 2-part mast, 125 hp Deutz air cooled engine on deck, wiggle tail, hydraulic puller, 3 winches on deck, 1 bumper winch, mounted on 1990 International 6 WD truck with 366 diesel engine, 59,000 miles, 6 speed transmission high/low, new tires, new batteries, alternator check, hydraulic hoses replaced, both hydraulic pumps rebuilt, spare hydraulic pump, good shape, 14” solid stem auger (new) Price: $92,500
ACKER AD-II (Ref#9399N)
Manufactured 1973, gas engine on deck, mounted on 1990 F800 4 wheel drive truck with gas engine, CDL required, running condition Price: $87,500
Tools available at extra cost
BRAINARD KILLMAN DRILL (Ref#8538T)
6 cylinder John Deere diesel deck engine, 10’ stroke, mounted on 2004 Ford Sterling with 400 hp Cat engine, low mileage, 2 rear hydraulic leveling jacks, front jack removed but available, no pipe or tools Price: $67,500
BUCK ROGERS 760 AUGER DRILL (Ref#9670T)
Trailer mounted, diesel engine, swivel attachment, sandline, extended derrick Price: $47,500
BUCK ROGERS DR2500 (Ref#12930Tc)
ARDCO SUPER L MINI AUGER DRILL BUGGY (Ref#9672T)
Currently set up for auger drilling, 4-cylinder Isuzu diesel engine, N P 4-speed transmission, Rockwell TRRT-32-79 transfer case, bumper mounted PTO driven Ramsey 400-L winch, 3-stage commercial hydraulic pump, 14’ lockable mast, hydraulic hoist drum, rod/auger rack. Can be converted to mud rotary drilling with addition of swivel (included) and mud pump (not included), unit runs strong and is light and fast, easily hauled and mobilized Price: $56,500
GEOTECHNICAL CUSTOM BUILT AUGER RIG (Ref#325T)
Built 2018, auger drill head, core head, auto hammer, 2 winches, 3.25” or 4.25” auger, N or H core rod, two available Price: $87,500 USD
Bobcat T550 with wireless remote package available at extra cost
ARDCAN K20 AUGER RIG (Ref#6091T)
Manufactured 1985, mounted on Ardco 6 x 6 carrier with Cat 3208 diesel engine, Norhill style tophead auger rig, driller's platform, toolboxes, no drill pipe, extra set of tires, Rockwell axles, hydraulic steering and brakes Price: $97,500
CME 1050 DRILL RIG (Ref#9163T)
Manufactured 2002, 3,149 hours as of October 2023, currently in service, 3 tower winches, New Moyno 3L10 pump, breakout table, 24,000 lb down pressure, 48,000 lb retract force, many new parts Price: $207,500
CME 1050 (Ref#13103Ta)
Manufactured 2002, quick disconnect mast, Cummins 6BT 5.9 turbo engine, side to side and in and out slide base, 10,000# main winch, 4000# aux winch, 200 lb tool winch, wireline/sandline winch, 140# auto hammer, Moyno 3L10 pump (new), 200 gallon water tank, toolbox, rod rack, extruder, 2 hydraulic auger racks, hydraulic rod clamp with breakout wrench, hydraulic chucks with 3-1/2" fluted Kelly, 2 rear and 1 front leveling jacks, mounted on CME buggy with Cummins diesel engne, automatic transmission Price: $169,500
CME 850 AUGER DRILL (Ref#6168T) Manufactured 1999, 4BT Cummins engine Price: $112,500
CME 850 (Ref#11920N)
Manufactured 1997, Cummins deck engine, track mounted, in-out and side to side slide base, 23' quick disconnect mast, angle capability, 140# auto hammer, breakout wrench, no cathead, Moyno 3L6 pump, 3 hoists, water tank, 3 hydraulic leveling jacks
Price: $135,000
CME 850 (Ref#12366T)
Manufactured 1988, Cummins 4BT engine (new), auto hammer, 3 winches, cathead, 3L8 Moyno pump, wiggle tail, breakout wrench, rod holder, new tracks Price: $62,500
CME 850 (Ref#1345R)
Manufacuted 1986, 2 winches, wireline, cathead, Moyno 3L6 pump, auto hammer Price: $115,000 PRICE REDUCED: $70,000
CME 750X ATV DRILLING RIG (Ref#4832Tb)
CME 750X ATV DRILLING RIG (Ref#8322T)
Built 2002, Cummins 6 cylinder diesel engine, high torque rotary drive 750, tandem hydraulic pump option, 2” hex auger drive, quick disconnect mast, cathead, 8500# hoist, 3200# hoist, 1800# hoist, wireline, Moyno 3L6, 140# automatic hammer Price: $177,500
Available at extra cost:
2005 Peterbilt 378 with 2013 Haulass LB35-T trailer
CME 750 ATV (Ref#12370T)
Manufactured 1995, mounted on ATV carrier, Cummins 4BT diesel engine, auto hammer, 3 winches, cathead, 3L8 Moyno pump, breakout wrench, rod holder, new tires and winch for carrier Price: $92,500
CME 750 DRILL RIG (Ref#3451Tb)
Auto hammer, 3 winches, 6 cylinder Deutz diesel Tier 1 engine, runs and drives great, no leaks, 50' hollow stem auger Price: $52,500
CME 750 AUGER DRILL AND TRUCK/TRAILER PACKAGE (Ref#5897T)
Manufactured 1972, Moyno pump, mounted on ATV buggy carrier powered by Ford 300 6-cyl gas engine, PTO, CME auto hammer, cathead, in/out slide base, 3 leveling jacks, auger racks, large tool box, water tank, 3 winches, quick disconnect tower. 2001 Freightliner FL70 with diesel engine and 31’ Roge trailer. Package Price: $50,000
CME 750 (Ref#2248T) Manufactured 1974, excellent condition, mounted on CME rubber tire buggy, 300 Ford Industrial motor (new 2017), 2 winches, 3L6 Moyno, auto hammer, rod holder and breakout wrench, ready to work Price: $62,500
CME 550X (Ref#13289T)
Manufactured 2009, Cummins 4BT diesel engine, 11,500 hours, rubber tired, angle package, automatic hammer, hydraulic rod clamp, breakout wrench, loaded Price: $187,500
CME 550X AUGER BUGGY DRILL RIG (Ref#5549Tb)
Manufactured 2008, 9000 hours, Bean pump, 140# auto hammer, slide base, angle capabilities, wiggle tail, rod clamp, fluted kelly, buggy has broken front axle Price, as is: $152,500
CME 550X AUGER DRILL (Ref#619Ta)
Manufactured 2004, 4600 hours, Cummins diesel engine, angle capability, auto hammer, 3 winches, wireline, 3L8 Moyno pump, new coupler, bearing plates, u joints, no leaks, runs great Price: $197,500
CME 550X BUGGY MOUNTED AUGER DRILL (Ref#395T)
Manufactured 2003, 140# auto hammer, wireline drilling capabilities, angle drilling capabilities, Bean piston style water pump, Cummins diesel engine and transfer case both recently replaced new, currently drilling, no tooling included Price: $101,500
CME 550X AUGER DRILL (Ref#9978T)
Manufactured 2001, B4.5 Stage V motor installed new in 2019, 3 winches, auto hammer, Moyno 3L8 pump, rod clamp, breakout table, 2 auger racks, recently repainted Price: $122,500
CME 550X (Ref#7245T)
Manufactured 1999, 3L6 Moyno pump, wireline, angle drive, in and out and side to side slide base, 3 winches, one wireline winch, winch on carrier, auto hammer, breakout table, quick disconnect mast, wiggle tail, breakout, 2 water tanks totaling 180 gallons, high torque rotary box, mounted on ATV rubber tire carrier, new tires, right angle drive rebuilt, set up for rock coring. Within past year replaced with new parts: Complete rebuild of rotary box (all new bearings, chain and both sprockets), replaced all drive shaft under carry, 4 new tires, new battery, replaced some of the hydraulic hoses where needed, new wires so safety systems work, new cable winch, new chain in auto hammer, replaced bearings in right angle drive, replaced seat, new alternator and starter, new water swivel on top of rotary box Price: $102,500
CME 550 BUGGY DRILL RIG (Ref#4781Ta)
Manufactured 1989, Cummins deck engine, in/out slide base, auto hammer, Moyno pump, (2) Pullmaster winches (PL5, PL2), 3200 lb gear winch, auger guard, water tank, no angle capability. Good condition, recently rebuilt both transmissions, power divider/PTO, rear differential and fuel pump, currently working. Price: $87,500
Also available at extra cost:
1990 VOLVO/AUTOCAR TRI-AXLE RIG CARRIER (Ref#4781Tb) Cat 3406 engine, 180,000 original miles
22 pieces of 3.75” x 5’ CME hollow stem auger, cutterhead, 2 drive heads, center plug
CME 550 ATV (Ref#12368T)
Manufactured 1988, Cummins 4BT diesel engine, auto hammer, 3 winches, cathead, 3L8 Moyno pump, breakout wrench, rod holder, new tires and winch for carrier Price: $62,500
CME 550 ATV AUGER RIG (Ref#8445T)
Manufactured 1988, auto hammer, 3L8 Moyno pump Price: $80,000
CME 550 (Ref#4258N)
Manufactured 1976, mounted on ATV with 300 gas engine, PTO, quick disconnect mast, in/out slide base, auto hammer, 3L8 Moyno pump, cathead, 100 gallon water tank, needs repairs Price: $29,500
CME 95 AUGER RIG (Ref#6305N)
CME 75 AUGER DRILL (Ref#9762Ta)
Manufactured 2008, no angle capabilities, 6 cylinder Cummins on deck, mounted on 2009 Mack truck, 410 hp Mack engine, 3 winches (1800#, 3200#, 8000#), Moyno 3L8 pump, 10 speed Fuller transmission, 140# hammer, hyd chuck (needs repair), needs new tires Price: $245,000
CME 75HT AUGER DRILL (Ref#7919T)
Mounted on Raymar tracks, Tier 3 Deutz engine with 4000 hours, 3 winch lines, auto hammer, rod gripper, water tank, Bean 35 pump. Includes a 2015 Peterbilt hauler with 660,000 miles (recently serviced by Peterbilt) Price: $235,000
CME 75HT (Ref#2541T)
Manufactured 1998, angle capability, wireline, diesel deck engine, Moyno 3L8, auto hammer, munted on 2013 Inrternational truck with diesel engine, CDl required Price: $242,500
CME 75 AUGER DRILL (Ref#12930Ta)
CME 75 AUGER DRILL (Ref#12930Tb)
Manufactured 1984, Cummins 6 cylinder diesel engine, 4 winches (7000 lb, 3200 lb, 1800 lbs), 3L8 Moyno pump, water swivel, 140 lb auto hammer, in/out side/side slide base, rod holder, breakout wrench, 500 gal water tank, toolboxes, mounted on 2002 International 4700 truck, 3 hydraulic jacks Price: $87,500
CME 75HT AUGER DRILL (Ref#4230T)
Manufactured 1990, mounted on Morooka MST1500, high torque rotary drive, Cummins 6 cylinder diesel engine, 4 winches 7,000 lb, 32,00 lb, 1800 lb and wireline, 3L8 Moyno water pump, water swivel, 140 lb auto hammer, rod holder, breakout wrench, stainless steel water tank and toolboxes, slide base in and out and side to side, 3 hydraulic jacks, front auger rack Price: $127,500
CME 75 (Ref#12372T)
CME 75 (Ref#14788T)
Manufactured 1985, mounted on Morooka MST 1500 tracked carrier with Mitsubishi 6 cyl diesel engine, Ford 300 engine, 3L8 Moyno, 400 gallon stainless water tank, one auger rack, 4 kill switches, 3 winches, 3 toolboxes, wiggle tail, wireline, breakout wrench, rig in good condition, 4491 hours on rig, 6698 on the Morooka, sitting one year, new tracks, no tooling PRICE: $97,500
CME 75 DRILL (Ref#3319T)
Unmounted, fully loaded, diesel drill with 8000 hours Price: $107,500
CME 55/75 AUGER DRILL (Ref#14790T)
CME LC60 TRACK MOUNTED AUGER DRILL (Ref#9762Tb)
Manufactured 1999, 4 cylinder John Deere engine, track mounted, Moyno 3L8 pump, remote control, 3227 hours Price: $147,500
CME LC60 (Ref#4885Tf)
Manufactured 1997 Price: $92,500
CME 55HT (Ref#9882T) Manufactured 2005, diesel engine on deck, Moyno 3L8 pump, mounted on 2005 GMC 7500 truck with diesel engine, auto hammer, breakout wrench, 25’ mast, in/out and side to side slide base, water tank, 3 winches, toolboxes Price: $232,500
CME 55 AUGER DRILL (Ref#3034T)
Manufactured 1991, Cummins 6 cylinder diesel deck engine, in out and side to side slide base, auto hammer, cathead, wireline and 3 other winches, fluted kelly, breakout wrench, no angle capability, mounted on 1991 International single axle truck with DT466 turbo engine, 3 hydraulic leveling jacks, good condition Price: $77,500
CME 55 AUGER DRILL RIG (Ref#4392T)
Manufactured 1991, cathead, in/out slide base, gas deck engine, Moyno Pump, Drive Shoe (2 weights that hammer), mounted on 1991 International dually with diesel engine, 2 rear jacks, pipe rack, includes tools and 120’ of 2” stem and 100’ of 3” steam Price: $47,500
CME 55 (Ref#12371T)
Manufactured 1990, Deutz6 cyl diesel engine, cathead, 2 winches, 3L8 Moyno pump, wiggle tail, breakout wrench, rod holder, mounted on 1990 Ford F700 truck, diesel engine, approx. 33,000 miles Price: $112,500
CME 55 AUGER DRILL RIG (Ref#9919Ta)
Manufactured 1989, mounted on 2007 International 4700 truck with diesel engine, gas engine on deck, 3 winch lines, auto hammer, breakout table, no Moyno pump, no cathead, approx. 227,500 miles, no CDL required Price: $77,500
CME 55 AUGER DRILL RIG (Ref#9919Td)
Manufactured 1988, mounted on 2004 International IH440 with diesel engine, Ford pony gas engine on deck, auto hammer, no cathead, no Moyno pump, no breakout table, approx. 90,000 miles, CDL required Price: $79,500
CME 55 (Ref#12363T)
Manufactured 1985, Ford Gas Industrial 300 engine, auto hammer, 3 winches, cathead, 3L8 Myno pump, siggle tail, breakout wrench, rod holder, mounted on 1998 Ford F800 diesel engine, 17,000 miles Price: $87,500
CME 55HT (Ref#9854T)
Manufactured 1984, gas deck engine, in/out and side to side slide base, Moyno 3L6 pump, auto hammer, cathead, breakout wrench, 3 winches, water tank, auger racks, 2 toolboxes, driller’s platform, mounted on 1999 GMC 6500 truck with diesel engine Price: $62,500
CME 55 (Ref#11729Ta)
Manufactured 1978, Wisconsin gas deck engine, in/out slide base, cathead, water pump, Moyno pump, water tank, no angle, SPT hammer, no auto hammer, mounted on 2000 International tandem axle truck with diesel engine (truck is having issues), 2 rear leveling jacks Price: $39,500 Price unmounted: $27,500
CME 55 (Ref#886N)
Manufactured 1973, completely gone through in nice condition, 6 cyl Ford gas engine, mounted on 1980 single axle Ford LN8000 truck with 1150 Cat diesel engine, cathead, 3 winches and wiggle tail, 6 ton Pitman hoist, Pitman hoist for loading/unloading augers 32’ reach ½” cable, (10) drill rods, (12) 8” hollow stem augers and drive head and bits, (6) new 4” hollow stem auger and drill head and bits, 4” solid stem auger bits, 6” solid stem auger and bits, (12) split spoons and hammers Price: $44,500
CME 55 (Ref#15056)
Manufactured 1973, mounted on Ardco buggy with gas engine, 300 6 cyl gas deck motor, 1 winch, cathead, hammer, 20’ of 2.24” HAS and AWJ rods Price: $72,500
CME 55 AUGER DRILL (Ref#5338T)
Built 1972, trailer mounted, Ramsey winch POR
CME 55 (Ref#12373T) Manufactured 1971, new 3 cylinder Deutz diesel engine, cathead, 2 winches, 3L8 Moyno pump, breakout wrench, rod h older, mounted on 1989 Ford F700 diesel motor, approx. 22,000 miles Price: $102,500
CME 55 AUGER DRILL RIG (Ref#9919Tb)
Manufactured 1971, mounted on 2002 GMC C7 4 x 2 truck with gas engine (needs new chassis motor), gas engine on deck, approx. 101,000 miles, 3 winches, auto hammer, manual transmission, no Moyno pump, no cathead, no breakout table, no CDL required Price: $72,500
CME 55 AUGER DRILL RIG (Ref#9919Tc)
Manufactured 1970, mounted on 2003 Ford F650 truck with diesel engine, diesel engine on deck, 3 winchlines, auto hammer, breakout table, no cathead, no Moyno pump, John Deere diesel pony engine, auto transmission, no CDL required Price: $120,000
CME 55 AUGER RIG (Ref#197T)
Rig built 1965, currently running and well maintained, mounted on 1993 Ford F600 2 x 4 truck with 6.6 diesel engine, Ford 4 lineline gas deck engine, New Moyno 3L4 pump, Diedrich auto hammer, 1 winch, cat head Price: $82,500
CME 55 TRACK MOUNTED AUGER DRILL (Ref#9164T) Diesel engine, no tools or augers Price: $57,500
CME 55 (Ref#1090T)
Manufactured 1967, older rig but runs, no angle capability, Ford 300 gas deck engine, in/out slide base, cathead, no autohammer, 2 winches, Moyno pump, auger racks, mounted on 1978 Chevy C65 truck with gas engine, 3 hyd leveling jacks Price: $18,500
CME 45C AUGER DRILL (Ref#3670T)
Manufactured 1997, rebuilt, angle package, Deutz 3 cyl. diesel deck engine, in and out slide base, no wiggletail, 2 winches 3000# and 5000#, 20’ mast, wireline, auto hammer, new water tank, new hoses, drillers platform, mounted on 2015 Freightliner M2 with Cummins diesel engine, 26,000 GVW, non CDL, 210,000 miles on truck, 2 rear & 1 front leveling jack Price: $102,500
CME 45C AUGER DRILL RIG (Ref#5358T)
Manufactured 1995, fully refurbished, new 3 cylinder diesel engine (3 hours), new transmission, new cylinders, new pump, 1 winch, auto hammer, cathead, wiggle tail, all new LED lighting, mounted on 1995 Ford F800 truck with Cummins 5.9L diesel engine (only 25,000 original miles) manual transmission, new front braeks, new tires, fully serviced, no CDL required Price: $200,000
CME 45C DRILL RIG (Ref#9763T)
Manufactured 1993, trailer mounted, 3 cylinder diesel engine, 2384 hours, angle drilling system, automatic SPT hammer, hydraulic rod clamp and breakout wrench, cathead, hydraulic hoist, skid winch, Moyno 3L6 water pump, 3 hyd jacks, 2 toolboxes, under deck rod storage, in/out and side to side slide base Price: $72,500
CME 45B AUGER DRILL RIG (Ref#6998T)
Manufactured 1991, 4 cyl gas engine on deck, wiggletail, auto hammer, rod holder, breakout table, no Moyno pump, mounted on 2002 International 7400 single axle truck, DT466 diesel, front winch, 2 rear jacks Price: $62,500
CME 45C (Ref#1823T)
Manufactured 1988, 1.8L White-Hercules 4 cylinder gas engine on deck (rebuilt with 400 hours), in/out slide base, no wiggletail, cathead, several hydraulic lines need replacing, mounted on 1990 Mitsubishi truck (truck is not good), sitting 4-5 years. Price, as is: $19,500
SHOP BUILT AUGER RIG (SIMILAR TO CME) (Ref#8944Ta)
Mounted on 1989 Ford F700 2WD truck with gas engine, no angle capability, grouter, 300 gallon water tank, 2 rear hydraulic jacks, 3rd jack just for the bed, running condition Price: $22,000
EARTH EXPLORATION MP500 AUGER RIG (Ref#5652T)
Manufactured 2008, auger, mud rotary and coring rig, 3 mast configurations: no mast can drill under 10’3”, hydraulic raised/lowered mast can drill 12’.5’ to 20’, Fixted mast can pull 20’ of auger, all hydraulic, mounted on 2006 Freightliner truck with 400 hp diesel engine, 3 hydraulic motors (each runs separate banks) 3000# hoist, 8500# hoist, 350’ capacity safety driver, 3L6 Moyno pump, 6-5/8” Gimbel, Allied AR62 hydraulic hammer for direct push, has turned 18” OD augers to 135’, well maintained, based off of CME and Mobile rigs, 59000 miles Price: $112,500
Available at extra cost:
(Ref#5652Tb) 18 pcs (90’) of 15” OD HSA, near new 10.25 x 5’ CME cap and bits POR
(Ref#5652Tc) 27 pcs (135’) of 18” OD HAS, near new 12.25 x 5’ CME cap and bits POR
MOBILE B-5500 (Ref#3565R)
Manufactured 1995, mounted on 1996 Ford L8000 tandem axle truck with diesel engine, 125,000 miles, multi-purpose dual speed top drive (14,000 ft/lb) drill for augering, mud rotary, or water coring (700 rpm). Long stroke mast (can use casing system or casing hammer), 18" auger capacity, 24" rotary capacity, hydraulic driven 5 x 6" mud pump, Moyno grout pump, water tank Price: $85,000
MOBILE B-3500 (Ref#4968Ta) Manufactured 1995, mounted on 1994 Ford F350 2WD drive, 7.3L diesel engine, PTO, 52,000 original miles, combination auger and direct push, Price: $54,000
TIEBACK/FOUNDATION DRILL RIG (Ref#8657T)
Used for tie back/foundation drilling, converted from auger drill, 4 speed Mobile drill head, Mounted on mJohn Deere 450 crawler dozer, will drill from below horizontal to almost vertical (but not designed to drill vertical), 3L8 Moyno pump, 50’ stroke, 10’ slide base, hydraulic clamp, breakout piston, auxiliary hydraulic outlet, can hold 4” string connected to head, (2) 40’ 4” strings lay in mast as well that are lifted by a hydraulic fork to connect to drill head Price: $57,500
MOBILE 92 (Ref#5574T)
135 hp 6 cyl Ford gas deck engine, 84" long slide base, 2 under unit auger racks, mounted on International 510 single axle truck with diesel engine (truck needs body work on floor), water tank available but not on truck, no auto hammer, no tooling Price: $22,500
MOBILE B-80 (Ref#1981N)
Manufactured 1986, excellent condition, mounted on Ford 8000 truck with Cat 3208 engine, PTO, hydraulic winch, 160# hammer, 300' of augers, split spoons, slips, AWJ rod, 22' stroke
Price: $77,500
MOBILE B80 DRILL RIG (Ref#2068Ta) Deutz diesel on deck, set up for auger and core, wiggle tail, sandline, mounted on 1976 International 2WD truck with gas engine, 4 hyd jacks Price: $72,500
MOBILE B-80 DRILL RIG (Ref#3387T)
Manufactured 1986, rig has a floating spindle installed for coring, et up for augering and large diameter core drilling, 22’ stroke, in/out slide base, breakout wrench, aux and main winches, no Moyno pump, no water tank, no auto hammer, mounted on 1986 Ford 6 wheel drive with diesel engine (early 1990’s truck), new right angle drive installed, , hydraulic foot clamp rotating, hydraulic breakout wrenches, hydraulic operated arms with winches, no tools Price: $42,500
Price with Bean 35 pump with Duetz diesel engine: $57,500
MOBILE B80 (Ref#10260T)
Manufactured 1978, 350 Detroit deck engine, mounted on 1981 Brigadier with 6092 truck engine, 9 sp transmission, no slide base, 50 gpm pump Price: $64,500
MOBILE BK-66 (Ref#8237R)
Manufactured 1995, Diedrich auto hammer, 3L6 Moyno pump, 2 winches, mounted on 1995 Ford F800 with Cat diesel engine Price: $57,500
MOBILE B61 HDX (Ref#7547T)
Manufactured 1990, Cummins 4BT 3.9 diesel engine (100 hp@2500 rpm), 3L8 Moyno pump, 8500# main hoist, 29' mast, mounted on Ford F800 truck with Ford 7.8L diesel engine (210 hp), 5 speed transmission Price: $84,500
MOBILE B61HDX (Ref#5637T)
Built 1991, Cummins 4BT deck engine, slide base, wiggle tail, wireline winch, plumbed for 3 more winches, no Moyno pump (but plumbed for one), water tank, (2) swing out auger racks, 3 leveling jacks, no auto hammer, mounted on 1991 Ford L8000 truck with 270 hp Ford engine, approx. 195,000 miles, Clark 28000 transmission, no rust, right angle drive needs repair (out of rig – has broken tooth – no chatter when running, took off to run another rig under repair), truck is hard to get in high gear PRICE: $47,500
MOBILE B-61 (Ref#3689R)
Manufactured 1991, Cummins 6BT deck engine, mounted on 1991 Ford F700 (not 4x4) with new diesel engine, no angle capability, in-out and side to side slide base, Moyno 3L8 pump, 3 winches, hydraulic cathead, no auto hammer or breakout, 300 gallon water tank, 4 hydraulic leveling jacks, owner has removed the automatic and 4 speed off of the rig, sitting but running when parked PRICE: $21,500
MOBILE B61 HDX (Ref#4238N)
Manufactured 1990, Cummins diesel deck engine, 3L6 Moyno pump, 3 speed Clark Model 28000 transmission on deck, mounted on 1990 GMC Brigadier 10 wheller with 671T Detroit, diesel engine, in/out side to side slide base, Moyno pump, no auto hammer, no cathead, safety driver, 200' of 4-1/4" augers, 120' of 6-5/8" augers, split spoons, sitting three years Price: $62,500
MOBILE B61HD AUGER DRILL RIG (Ref#9045T)
Manufactured 1989, 3.9L 4-cylinder Cummins diesel deck engine, mounted on 1989 ford F900 ruck with diesel engine, 171,000 miles, Moyno 3L6 pump, Safety driver winch and hammer, Automatic SPT Geotech hammer, rod clamp, main winch, auxiliary winch, cathead, slide base, wiggle tail, pipe rack, toolboxes, 400 gallon poly water tank, 3 leveling jacks, 8900 ft/lb torque, 92 – 583 rpm Price: $52,500
MOBILE B61 (Ref#12374T)
Manufactured 1989, Cummins 4BT diesel engine, cathead, 2 winches, 3L8 Moyno pump, breakout wrench, rod holder, mounted on 1989 Mack diesel motor, 12,238 miles Price: $92,500
MOBILE B61 HDX (Ref#8086T)
Manufactured 1985, set up for auger and coring, 4 x 5 Gardner Denver mud pump, Detroit 353 deck engine, auto hammer, slide base, hydraulic breakout, mounted on 2001 Freightliner truck wityh Detroit engine, no angle capability, 100' flight auger, coring equipment and subs Price: $47,500
MOBILE B61 HDX (Ref#8238Rb)
Manufactured 1984, 300 Ford 6 cylinder engine on deck, Gardner Denver air compressor, cathead, mounted on 1991 International 4900 truck Needs work Price: $39,500 PRICE REDUCED: $32,500
MOBILE B-61 AUGER RIG (Ref#7269Ta)
6 cylinder Ford gas engine, mounted on 1979 Ford 9000 tandemax axle truck, new Cat 3208 diesel engine and clutch, Road Ranger transmission, 65' hollow stem augers, slide hammer, set up for split spoon soil augering (split spoon sampler or inner rod for split spoon not available) Price: $23,500
MOBILE B61 (Ref#12732T)
Manufactured 1988, Moyno pump, Bean 35 pump, hydraulically driven rig, hydrostatic drive, 3 winches, 30' mast, new hydrauliuc pump, mounted on 1983 Ford 8000 6 x 6 truck, 3 leveling jacks, ready to work Price: $57,500
MOBILE B61HD (Ref#15007T)
Manufactured 1980’s, trailer mounted, Ford 6 cyl gas engine, cathead, in/out slide base, 2 winches, Acker chuck head, 3 leveling jacks Price: $44,000 CDN
MOBILE B59 (Ref#12463T)
Manufactured 1991, Cummins diesel on deck, 3L6 Moyno pump, in/out and side to side slide base, mounted on Ford F800 with Cummins diesel engine, auger racks, sitting since 2013, starts and runs Price: $87,500
MOBILE B-59 (Ref#4912Ta) Mounted on 1993 International truck with Cummins diesel engine, no auto hammer, freefall, 4 winches, in/out and side to side slidbebase, no cathead, 350 gal water tank, 3L10 Moyno pump, excellent condition Price: $62,500
MOBILE B58 AUGER DRILL (Ref#1685Tb)
MOBILE B57 (Ref#8669T)
Manufactured 1994, New Ford 300 Commercial deck engine, mounted on 1994 Ford F800 truck (just serviced by dealer, new brakes), low mileage, automatic transmission, new tires, Moyno 3L8 mud pump with new hydraulic motor, 3 winches, cathead, auger racks, water tank Price: $31,500
MOBILE B-57 AUGER DRILL RIG (Ref#8195T)
Manufactured 1991, gas deck engine, 250 gal water tank, cathead, in/out and side to side slide base, no pump, no autohammer, mounted on 1995 Ford F700 single axle truck (not 4 x 4) with gas engine Price: $39,500
MOBILE B57 AUGER DRILL (Ref#4283T)
Rig runs, truck not DOT worthy, truck will start but will have to be trailered Price: $24,500
MOBILE B57 AUGER DRILL RIG (Ref#3314Ta) Ford Industrial 300 gas deck engine, cathead, sandline, winch line, no pump, mounted on Ford truck, 3 hyd leveling jacks, fold out auger racks Price: $37,500
Augers available at extra cost
MOBILE B57 (Ref#4600T) Mounted on 1989 Ford F700 single axle truck with gas engine, Ford deck engine, automatic hammer, 2 winch lines, extruder, Moyno water pump, 1 front and 2 rear leveling jacks Price: $85,000
MOBILE B57 BUGGY DRILL RIG (Ref#457Ta)
MOBILE B-56 (Ref#11448Ra)
Manufactured 1970, mounted on 1994 International 4900 truck, DT466 engine, 500 gal water tank, Moyno pump, cathead, 1 winch, slide base, 2 pullout auger racks Price: $35,500
MOBILE B-54 AUGER RIG (Ref#1279Ta)
Available at extra cost:
35 TON KAUFMAN DETACHABLE GOOSENECK TRAILER (Ref#1279Tb) Air ride, dovetail package, 66,000 GVWR, frame is 4 cambered main beams fabricated with 100 KSI (t1) and 80 KSI high tensile steel, 36” steel dovetail with traction cleats, Removable hydraulic tongue-non-ground bearings gooseneck with 3 position adjustable load blocks and 89” – 107” available swing clearance (standard set up for wet line), SAE 2” Kingpin couple (16” Kingpin setting), forged A-rig tie downs, 25’ deck length, 102” deck width, 24” deck height, brakes all shweel 16.5” x 7” air brakes, automatic slack adjusters and 4S/2M ABS, (2) 25,000 lb axles (5” round, 5/8” wall thickness), air ride suspension.
2000 WESTERN STAR 4900 (Ref#1279Tc) 6 cylinder, approx. 588,200 miles
Package Price: $320,000
MOBILE B53 CORE DRILL (Ref#1135T)
Manufactured 2000, Detroit deck engine, mounted on Ford F700 truck with Ford diesel engine, 300’ of 10’ pipe, running condition Price: $23,500
MOBILE B53 (Ref#8034T)
Manufactured 1990, PTO, mounted on Gemco GT3004 x 4 articulating log skidder with 4 cyl Detroit 453 diesel engine, front winch, cathead, side to side slide base, no Moyno pump, auger racks, 10' side rack, 60 gal water tank, 140# safety/slide hammer, set up for 6-1/4" auger, 2 rear jacks, running condition Price: $25,000
MOBILE B53 (Ref#11889Ta)
Mounted on Ardco buggy, Detroit diesel, angle capability, Moyno pump, in-out slide base Price: $44,500
MOBILE B53 (Ref#1128Tb)
Manufactured 1979, mounted on Wood Tiger Cub Model M114 with gas engine, cathead, 2 winches Price: $32,500
MOBILE B-53 (Ref#13469)
Manufactured 1979, mounted on Ardco JXF buggy, 425 Bean pump, 3 hoists 7000#, 2900# and safety driver, new hydraulics, PTO, Detroit diesel in buggy, 250 gallon water tank, 20,000# winch on front PRICE REDUCED: $32,500
MOBILE B53 (Ref#8442R)
Manufactured 1989, mounted on 1986 Bombadier, Perkins diesel motor, side to side slide base, 3L6 Moyno pump, no autohammer, 2 winches, no cathead, 3 leveling jacks Price: $55,000
MOBILE B53 (Ref#774T)
Manufactured 1995, Refurbished 2012, auto hammer, in/out slide base, 2 working winches, third winch needs to be rebuilt, auto hammer, 3L6 Moyno pump, no water tank, no breakout wrench, mounted on 1995 Ford F800 4 x 4 truck with new diesel engine (300 hours), PTO Price: $52,500
MOBILE B-53 (Ref#8781T)
Manufactured 1986, mounted on 1986 Ford F700 4 x 4 truck, 8.2 Detroit diesel, PTO, 171,000 miles, 25' auger, 3 cutterheads, in and out slide base, cathead, no Moyno pump Price: $37,500 PRICE REDUCED: $29,500
MOBILE B-53 (Ref#9752Na)
Unmounted, Manufactured 1980, 353 Detroit deck engine, hydraulic chuck, extended mast, in-out slide base, cathead, mainline, sandline & wireline winches, no auto hammer, 435 Bean pump, underbody swing out auger rack, toolbox, no water tank, 3 hydraulic leveling jacks (truck in photos is not available) PRICE: $31,500
MOBILE B-53 (Ref#10054Td)
Manufactured 1975, mounted on Bombadier Musket crawler, cathead, 4 leveling jacks, hyd winch, mechanical winch on carrier Price: $39,500 CDN
MOBILE B-50 (Ref#3406N)
Manufactured mid 1970’s, mounted on 1963 Chevy C60 series truck (truck needs work) 235hp 6 cyl engine, PTO, tophead swivel for air and mud, in/out and side to side slide base, cathead, tailout line, 50’ of 6” auger, 90’ of 2-5/8” drill pipe, 20’ of 8” overdrive drill casing, 6” and 8” cutter bit, outriggers on rear end, aux hydraulic tank PRICE: $32,500
MOBILE B-50 (Ref#4186T)
Rebuilt 1984 (at Mobile), 6 cyl gas deck engine (replaced 2004), safety driver, Moyno pump, extended mast to 20' (extended by Mobile), mounted on 1984 F700 awd truck with gas engine, cathead, aluminum toolboxes, auger racks, 40' of 6-5/8" hollow stem auger, last drilled Feb 2019 Price: $29,500
MOBILE B48X TRACK MOUNTED AUGER DRILL (Ref#5581T)
Built 2019, only 60 hours, mounted on Cat 307 carrier, Moyno 3L8, in and out and side to side, auto hammer, 3 winches, breakout, rod holder, Tier 4 John Deere engine, all hydraulic, 1500 rpm. 2013 International Rollback carrier available at extra cost. . Price: $295,000
MOBILE B48 DRILL RIG (Ref#13031T)
Manufactured 2014, approx. 2400 hours, Moyno 3L6 pump, auger guard, in/out and side/side slide base, 8500# winch, 2500# winch, 1200# winch, hydraulic breakout wrench, hydraulic rod clamp, SPT auto hammer, 250 gallon water tank, drill head rebuilt 2019, PTO rebuilt 2019, engine harness and wiring replaced 2019, excellent condition, ready to work, all hydraulic Price: $224,500
MOBILE B47 AUGER DRILL RIG (Ref#619Tb)
Manufactured 1995, Deutz ediesel engine, cathead, winch, hydraulic driven, Marooka carrier, no leaks, runs great Price: $87,500
MOBILE B47 (Ref#8479T)
Manufactured 1984, no pump, mounted on 1984 Ford F700 truck with diesel engine, PTO, in and out slide base, not side to side slide base, STP hammer, 2 winches, cathead, hammer Price: $47,500
MOBILE B40L (Ref#13525T)
Manufactured 1978, in-out slide base, 2 lines (winch and freefall line), no cathead or sandline, no water tank, 32' mast, mounted on 1978 Ford 8000 truck with Cat engine, PTO, currently drilling Price: $62,500
MOBILE B40L (Ref#4455Ta)
Manufactured 1984, 6 cylinder gas engine on deck, 17’ stroke, Moyno 3L6 pump, spudder system, mounted on 1984 tandem axle International truck with DT466 diesel engine, 500 gallon water tank, 4 leveling jacks, air brakes, CDL required Price: $51,500
MOBILE B40H (Ref#4455Tb)
Manufactured 1960’s, 5’ stroke, 2L4 Moyno pump, 200 gallon water tank, cathead, 4 speed gear box, mounted on single axle truck (needs new truck), 3 leveling jacks Price: $19,500
MOBILE B40H (Ref#1128Ta)
Manufactured 1969, mounted on 1990 Ford F700 single axle truck 2WD (approx. 96,000 miles), Ford 6.8L engine, Eaton Fuler manual transmission, 2 speed rear axle, 300 gal water tank Price: $14,500
MOBILE B33 DRILL RIG (Ref#6670T)
Manufactured 2003, trailer mounted, Deutz 4 cylinder engine, 2L6 Moyno pump, 150 gallon water tank, safety driver, winch, extra hydraulic bank room, wiggle tail, high speed head, low torque head, slide off hole, safety shut offs, telescopic tower, 11' stroke, hydraulic cooler, 3 jacks, tool boxes, 231 original hours Price: $61,500
MOBILE B33 (Ref#2487T)
Mounted on 2 axle trailer, Ford Industrial 4 cyl deck engine, front to back slide, winch, cathead, rig is gearbox and kelly driven, timing is off but rig starts and runs Price: $19,500
MOBILE B30S (Ref#2486T)
24' boom, modified to side to side and front to back, mounted on 1990 Ford F450 truck, 7.3 diesel engine, approx. 75000 miles, sitting since 2000, broken windshield, 2 new batteries, 2 new front tires Price: $15,500
MOBILE B30 AUGER DRILL RIG (Ref#4555T)
Mounted on 1998 Freightliner truck with 5.9 Cummins diesel engine (roadworthy), 6.9 Ford diesel deck engine gone through in 2019, 30’ of 4” auger and tooling Price: $52,500
MOBILE AUGER/CORE RIG (Ref#2084TB) Mounted on 1998 Ford F800 truck, 2” x 5’ up to 8” x 5’ auger bits, 2” x 5’ drill pipe, ready to work Price: $32,500
MOBILE B24 LOW CLEARANCE AUGER RIG (Ref#4201T)
Manufactured 1994, good for low clearance, only 180 hours, Detuz Z790 diesel deck engine, cathead, rig mounted on square box frame with jacks, working condition Price: $15,500
Tooling available at additional cost
INGERSOLL RAND A-300 (Ref#3529N)
Manufactured 1993, mounted on 1993 Ford truck with diesel engine, PTO driven, cathead, 2 winches, 3L8 Moyno pump, in/out slide base, head moves side to side, has duel head (one for augers and one for coring), telescoping tower can be used for low clearance, high rail gear (can be used on railroad tracks), good running condition, no tools PRICE REDUCED: $42,500
INGERSOLL RAND A-300 (Ref#5938)
Manufactured 1994, 3L6 Moyno pump, Mounted on 2016 Ford F650 (not 4x4) with Cummins engine, PTO, 3 jacks, 19' telescoping mast, 8' head travel 8,000 ft/lb, hoist, cathead, slide base, in-out, side to side slide base, wiggle tail, 150 gal water tank, (2) auger racks, (2) tool boxes PRICE: $95,000
INGERSOLL RAND A-200 AUGER RIG (Ref#2871T)
Built 1984, trailer mounted, 10’ stroke, Perkins/Detroit diesel engine, safety hammer, includes 20’ of 3-1/4” hollow stem auger Price on Request or Make Reasonable Offer
BIG BEAVER AUGER DRILL (Ref#4220T)
Pop up on wheels, 22 hp Honda engine, pully hammer, new fuel tank, approx. 400 hours, 12 augers included, currently working Price: $29,750
SEISMIC AUGER DRILL (Ref#3480T)
Manufactured 1981, 3” Moyno pump, mounted on 1981 GMC tandem axle truck with 671 Detroit diesel, 13 speed transmission, 3TA aux. transmission (runs rig), no cathead, no auto hammer, 300’ auger. Skid mounted Geoloop 50-500 grout pump with engine Price: $72,500
SEISMIC AUGER DRILL (Ref#4544RA)
Manufactured 1985, mounted on 1995 Freightliner FL80, Cummins 8.3 engine, PTO, new 4 stage P75 hydraulic pump, 3” Moyno pump, staff rotary head, 900 gallon water tank, no auto hammer, includes flotation tires Price: $27,500
COMTRAK SEISMIC AUGER DRILL (Ref#4544RB)
Manufactured 2001, track mounted with 4 cyl Cummins engine, can drive from cab or rear, rebuilt Tempest 12 air compressor (less than 100 hours), 5’ mast, handles 5’ drill pipe, water drilling capabilities, 130 gallon water tank, new hydraulic pump, new tracks, many spare parts PRICE: $37,500
SHOP BUILT TRACK MOUNTED AUGER/MUD ROTARY DRILL RIG (Ref#619Tc)
Manufactured 2015, Kubota engine with 210 hours, track drill, no hammer, can auger or mud rotary with external pump or there is a place for pump to be installed, like new Price: $52,500
TMG AUGER DRILL RIG (Ref#3080T)
Built 2019, ML Series head, 74 hp, 9168 ft/lb torque, 4 speed gear box drill head, 1000-1500’ depth capacity, 74 hp Tier 4 turbo charged diesel engine, mounted on 2012 Ford F750 4x2 Truck with Cummins diesel engine, non CDL Price: $152,500
TMG-37 AUGER DRILL RIG PACKAGE (Ref#2932T)
Manufactured 2022, track mounted, 20 rpm rotary drill head, 3500 ft/lbs torque, 37 hp Kohler gas air-cooled engine, 140# hammer, 39” drop height, confirms to ASTM D-1586 for SPT sampling, mini winch tower, high force extraction cylinders with 48000 lb lift force, rubber tracks, wired remote, NON CDL
50’ of 2” SPT rod
Price for rig and SPT rod: $87,500
TMG BOXER DRILL ATTACHMENT (Ref#189T)
Manufactured 2012, 50 hp engine, unmounted, 4’ mast with 5’ adapter extension for mast (skid steer, auger attachment and forklift attachment not available) Price: $16,500
SIMCO TR2-4000 DRILL RIG (Ref#4290T) Built 1995, Deutz diesel engine, track mounted Price: $37,500
SIMCO 4000 TR2 (Ref#10829T)
Track mounted, Deutz 4 cyl diesel engine - 2009, no pump, angle capability, 2 speed head (core/drill), 6140 lb max head speed, 7500 bls down pressure, 8500 lbs pullback, 90’ per minute winch speed, 160” mast with additional extension – 228” total, 5” bit, 2 core barrels Price: $22,500
SIMCO 2800 DRILL RIG (Ref#6560T)
Manufactured 2001, Mounted on Ford Super Duty, PTO (new), rebuilt 2 x 3 centrifugal mud pump, mud pan, pipe rack, 200’ of 10’ rods, currently working Price: $107,500
SIMCO 2800 HS/HT AUGER DRILL RIG (Ref#3277Ta)
SHOP BUILT RIG (Similar to Simco 2800) (Ref#8967Ra) Manufactured 2003, mounted on 2004 Ford F650 truck with Cat C7, centrifugal pump, 40’ auger, 60’ drill rod, safety hammer, PTO, 60,000 miles on truck (Oct 2015) Price: $77,500
SHOP BUILT RIG (Similar to Simco 2800) (Ref#8967Rb) Manufactured 2007, mounted on 2004 Ford F650 truck with Cummins engine, centrifugal pump, 40’ auger, 60’ drill rod, safety hammer, PTO driven Price: $87,500
SIMCO 2800 (Ref#11729Tb)
Manufactured early 1970's, 5' stroke, trailer mounted with 4 cyl Wisconsin gas engine, 2 winches, no jacks, in/out slide base Price: $11,500
SIMCO 2800 (Ref#7201R)
Manufactured 1980’s, mounted on Ford truck with no engine, single line winch, set up for augering, in-out and side to side slide base, cathead, auger racks, 1 front & 2 rear hydraulic leveling jacks, no mud, no tools PRICE: $11,500
SIMCO 2400 DRILL RIG (Ref#2427T) Manufactured 2020, mounted on 2020 Marooka 600 with diesel engine, 10’ stroke, 3 cyl deck engine, plubed for mud pump, bare rig with no tools Price: $292,500
SIMCO 2400 (Ref#8065T)
Totally rebuilt. Wisconsin 4-cylinder gas deck engine, 140lb hammer, winch, cathead, mounted on 1999 Chevy Dually 1-ton 4 x 4 truck with gas engine, extended mast, auger rack, under box storage, two open valves to add on other tooling possibly an auto hammer for SPT testing
Rebuilt:
Frames inspected scraped, rust removed and undercoated
Truck brake lights replaced
Drill engine flushed and tested and necessary items replaced
Rig engine has new starter motor
New hydraulic pump and hydraulic hoses.
New winch cable
Rig sandblasted, repaired and painted
New hydraulic fluids and filters
New pressure gauges installed
New hydraulic ram to raise and lower mast installed, mast slide rails replaced
New rig starter key
Tooling/auger and rod included:
25’ of Diedrich 3-1/2" solid stem flight augers
25’ of Diedrich 3-1/4" hollow stem augers
(2) 2” split spoons with split spoon extender
4" x 4' Shelby tube with drive rod
25’ threaded drill rod
2 cutting heads for 3-1/4” HSA
Winches,
Connecting bolts and pins,
Cats eye for rod hoisting,
Kwik Klamp for rod holding
Safety shoe for auger removal
Package Price: $92,500
SIMCO 2400 DRILL RIG (Ref#1080T)
10’ stroke, Cummins engine (new 2017) on deck, mounted on Ardco chassis with Duetz engine installed 2018 but engine is burnt, winch, new hydraulic hoses 2017, toolbox Price: $40,000
SIMCO SK2400 AUGER DRILL (Ref#2047T_simco)
Manufactured 2005, truck mounted Price: $29,500 USD
SIMCO 2400 DRILL RIG (Ref#4313T)
Mounted on 2009 Ford F550 2WD truck with 6.4 power stroke diesel engine, approx. 151,300 miles, hydraulic air compressor, sliding platform, gas deck engine, percussion hammer, good running condition but has a minor hydraulic leak Price: $27,500
SIMCO 2400 (Ref#4299T)
Manufactured 1996, unmounted, John Deere diesel engine, Moyno 2L4 pump (not installed on rig), in/out slide base, only has one 100 torque head, no high speed head, SPT hammer, cathead, 1 winch PRICE: $45,000
SIMCO 2400 (Ref#7935Ta)
Manufactured 1996, Kohler 34 gas deck engine (California compliant), set up for geotechnical, in/out slide base, mounted on 1985 Chevy 2 wheel drive with diesel engine, cathead, winch, no auto hammer, No Moyno pump, fully operational Price: $39,500
Available at extra cost: Shop built portable hand held probe (similar to Geoprobe), good for limited access
GEFCO STRATASTAR 25 (Ref#8231R)
Manufactured 1996, mounted on 1996 International 4900 with DT466, approx. 81,000 miles, 3 winches, 3L8 Moyno pump, SS water tank, fluted kelly, rod table with breakout wrench, (2) swing out auger racked Price: $63,500
GEFCO STRATASTAR 5 AUGER DRILL (Ref#10761T)
Manufactured 1996, approx. 2570 hours, Deutz BF4L1011 diesel 72 hp deck engine, mounted on 2009 Ford F550 34 x 4 truck, 114,000 miles, diesel powerstroke truck engine, 16" on/off hole slide base, 5000# torque rotary tophead, 72" feed travel, 9'6" corwn block, 2 rear and 1 front hyd leveling jacks Price: $57,500
FAILING F10 (Ref#4885Td)
Manufactured 1990, diesel deck engine, mounted on Ford L9000 with diesel engine Price: $77,500
FAILING F10 (Ref#11968Nc)
Manufactured 1990, set up for core/auger/water and air rotary drilling, mounted on 1990 International 4900 6x4 with DT466 diesel engine, Gardner Denver 5x6 mud pump, Moyno 3L8 pump, 2 winches, new Cummins deck engine (less than 300 hours), deck mounted hydraulic drive 2000psi steam cleaner/power washer, toolboxes, auger rack Price: $122,500
FAILING F9 (Ref#14445T)
Manufactured 2002, Deutz deck engine, mounted on Interantional truck with diesel engine, Cummins deck engine, angle capable, in/out and side to side slide base, water tank, Moyno pump, no auto hammer, cathead, no tools or augers PRICE REDUCED: $97,500
GEFCO/FAILING AUGER DRILL RIG (Ref#3160T)
Manufactured 2004, (3) winches, mud pump (needs to be gone through), mounted on 2004 Ford F550 Super Duty Power Stroke diesel 6.0 engine, approx. 131,000 miles, rig and truck recently serviced with new oil and filters, new front suspension with new rods, new steering chock/dampener, sway bar and bushings, sway bar links and bushings. New power steering pump, new serpentine belt, new front and rear brakes. Includes 120’ drill rod, flight auger, SPT set up with automatic hammer, rock bit, 2’ x 4’ extension rods, sampling tubes. Price: $112,500
FAILING F6 (Ref#11968Na)
Manufactured 1990, core and auger drill, mounted on 1990 International 4900 with DT466 diesel engine, 2 winches, Moyno 3L8 pump, electric over hydraulic controls, Cummins 4BT deck engine, deck mounted 2000psi steam cleaner/power washer, toolboxes, auger racks Price: $57,500
GIDDINGS 2400 LIMITED ACCESS RIG (Ref#12740Ta)
Mounted on 1990’s Suszuki jeep, all aluminum, Kohler Command 25 engine, rotary head, fully operational Price: $25,000
MOBILE MINUTEMAN (Ref#12740Tb) Briggs & Stratton 10 hp gas engine, Acker Tripod with Briggs & Stratton 8 h gas engine, cathead, used for sampling, misc parts Price: $13,500
ALTEC DIGGER DERRICK (Ref#5463Ta)
John Deere diesel engine, mounted on 2003 International truck with diesel engine, 2 rear hydraulic leveling jacks, tools and bits Price: $100,000
GEOTECHNICAL, ENVIRONMENTAL AND MINERAL EXPLORATION COMPANY FOR SALE (Ref#9774T)
CME 45B AUGER DRILL Mounted on Bombardier Muskeg
CME 45C AUGER Mounted on trailer
CME 55 AUGER DRILL Mounted on truck
CME 55 AUGER DRILL Mounted on truck
Full compliment of augers, flush joint casing, N size and H size tooling, 1000’s of feet of rod, down hole hammers (3” to 8”0
Simco electric drill
Sprague and Henwood electric drill
Trailers, trucks
All equipment in working condition, many tools, parts, etc accumulated over 40 years of business
Price for equipment, name/phone and client list: $800,000
DIRECT PUSH AND CONE PENETRATION RIG
AMS 9630-PRO POWERPROBE (Ref#6800Ta)
Manufactured 2002, 60 hp diesel engine, 72” mast stroke, 10,000# Prince winch mast mounted without cable, 6000 ft/lb torque, 2-speed auger mtoor, 2” hex output shaft, direct push hammer, 5’ hydraulic extruder, approx. 2760 hours.
2013 Ford F550 crew cab, very good condition and
Yanmar Crawler Model TFW4
Price: $90,000
AMS 9635-VTR-S POWER PROBE (Ref#6800Tb)
Manufactured 2005, 47 hp liquid cooled Isuzu diesel engine (non-turbo), 72” mast stroke, 3000 lb overhead winch, 3,500 ft/lb torque, 2-speed auger motor, 40 rpm low/150 rpm high, 2” hex output shaft, 350 ft/lb BR333 Allied Direct push hammer (added to machine 2014), 5’ hydraulic extruder, chain vise, storage compartments, new tracks, wireless remote Price: $53,500
AMS POWERPROBE 9600PRO (Ref#3825T)
AMS POWERPROBE 9600 (Ref#4165R)
Manufactured 2001, mounted on 2001 Ford F550 truck wih rebuilt 7.3L diesel Price: $44,500
AMS 9600-VTR POWERPROBE (Ref#14448T)
Track mounted, manufactured 2007, diesel engne, with trailer Price: $54,000
AMS 9410-D POWERPROBE (Ref#1079Ta)
Available with:
VERTEK CPT SYSTEM (Ref#1079Tb) Controlled down feed system, controller datapak, 1.75 cone assembly 20 ton, 50m 10 pin cable, DPT encoder, (32) CPT rods 1.75 rope THD 1m, (8) cone tips 1.75, package of 10 cone filters, (4) friction sleeves 1.75, (2) retainerrings, 0-ring kit, dual anchor CPT system (2) 4’ anchors w/4’ extensions, single anchor CPT system 5’, CPT pull CAPS, CPT anvile, (2) Seismic VTK PNP trigger assembly 25’, (2) trigger mount plates Price for CPT System: $41,500
GEOPROBE 7822DT (Ref#5351T)
Manufactured 2011, approx. 4700 hours, tier 4 engine, truck mounted, auger head, auger cube, winch, Moyno pump, macro core extruder, auto hammer Price: $175,000
GEOPROE 7822DT (Ref#8653T)
Manufactured 2009, Kubota diesel engine, hydraulic extruder, winch, front dro rack (not shown), side tray, 140 lb SPT hammer mounted (hammer available at extra cost), 2 speed auger head, well maintained Price: $108,500
GEOPROBE 7730DT (Ref#4268T)
Manufactured 2009, Kubota V330 engine, automatic hammer, high speed auger, dual motor head, track mounted, 585 hours Price: $80,000
GEOPROBE 7730DT (Ref#13702R)
Manufactured 2005, direct push, no auto hammer, mounted on tracks, auger attachment, liner extractor, rod rack, 4 cyl Kubota diesel engine, plow blade in rear, 800 Nitrogen Charge PSI for hammer, 7’ stroke, remote, 6000 hours, well maintained Price: $72,500
GEOPROBE 7720DT (Ref#7416T)
Manufactured 2008, hour meter replaced at 7167 hours, new meter reads 1626 hours – total hours 8793, Geoprobe GH60 hammer, auto drop hammer, Kubota V2003-TE engine. Rig has a crack in frame, work done within past year: tower fold pins replaced, new hammer anvil, probe cylinder rebuilt, winch cylinder rebuilt, hammer mount wear pucks replaced, cylinder wear strips replaced, mast slides replaced. Engine well maintained and oil and filers changed as required. Price as is: $72,500
GEOPROBE 6620DT (Ref#7593R)
Manufactured 2004, Kubota diesel engine, percussion hammer, track mounted, remote control, no tooling Price: $62,500
GEOPROBE 6620DT (Ref#6629T)
Track mounted Price: $47,500
GEOPROBE 6600 (Ref#6056T)
Manufactured 2004, 497 hours, new hoses, rebuilt main cylinder, hydraulic extruder, mounted on 2004 Ford F650 w/Cat 3126E diesel, approx. 47,000 miles, new tires, new brakes, GH60 hammer Price: $122,500
GEOPROBE 540B (Ref#9736T)
Manufactured 2000, mounted on Case 1840 skid steer, probe needs GH40 upper assembly, skid steer runs great, hour meter broken on probe, works on skid steer 5671 hours on both, unit was used as a backup for the past 5 years, includes bucket for skid steer, no tooling Price: $35,500
GEOPROBE 5400 (Ref#10462T)
Manufactured 2009, mounted on 2009 Ford 450 4 x 4 with Cummins engine, low mileage, GH42 hammer, no remote control, approx. 50,000 miles, sitting 2-1/2 years Price: $23,500
GEOPROBE 5400 (Ref#6614T)
Manufactured 2001, 3393 hours, Munchi pump, mounted on 2000 Chevy 2500 truck with gas 350 5.7L engine, (needs tires) 18,000 miles, 50 gal water tank, hydraulic oil cooler, misc tooling Price: $37,500 PRICE REDUCED: $29,500
GEOPROBE 5400 (Ref#8394T)
Manufactured 1999, unmounted (probe only), PTO, Geoprobe hammer, misc tooling Price: $29,500
GEOPROBE 5400 (Ref#7260T)
Manufactured 1997, unmounted, everything works, new hammer Price: $10,500
GEOPROBE 5400 (Ref#4564T)
Manufactured 1994, mounted on 1998 Chevy 2500 pickup with gas engine, 133,337 miles, suspension recently done, no remote, no tooling (serviced by Geoprobe 2020) Price: $36,500
GEOPROBE 5400 (Ref#2156T)
New tracks, new breaking system, rebuilt hammer Price: $37,500
GEOPROBE 54DT (Ref#5616Ta)
Mounted on tractor Price on Request
SIMCO EARTHPROBE 200 (Ref#15533)
Manufactured 1997, Kohler 18 hp gas engine on deck, mounted on 1997 Ford F250 w/powerstroke diesel, good condition, last used 2004, been in storage, hammer rebuilt 2020 and never used, no hydraulic pump, no tools or augers Price: $28,500
GEOPROBE 420M (Ref#5616Tb)
No power unit Price: $17,500
AMS POWERPROBE 9600 (Ref#3064Ta)
Manufactured 2006, only 1900 hours, unmounted, 60' of 4-1/2" HSA, sampling tubs, many tools Price: $42,500
Extensive tooling available at additional cost (Ref#3064Tb)
SHOP BUILT PORTABLE HAND HELD PROBE (SIMILAR TO GEOPROBE) (Ref#7935Tb)
Good for limited access, probe only, no power Tooling: 60’ of 1” rod, 30’ of 5/8” rod, split spoons Price: $10,500
RAMAC GROUND PENETRATING RADAR (Ref#8433T)
Ramac monitor, 12 volt, cart included Price: $11,500
USED AUGER AVAILABLE:
(Ref#15489R) Diedrich 6 1/4 ID hollow stem augers (95% new – ½ never used and ½ only used twice), 50’ with center plug, barely used, like new condition Price on Request
(Ref#5653Rb) 11 pcs of 6-5/8" hollow stem augers 4-key Price: $5,300
(Ref#507T) - HOLLOW STEM AUGER AND TOOLING
60’ - 2.25 (Mobil)
55’ - 2.25 (CME)
15’ - 4.25 H.D(CME)
25’ - 6.25 light(CME)
50’ - 6.25 H.D(CME)
20’ - 10.25 H.D(CME)
35’ - 12.25 H.D(CME)
Extras:
6.25 light 2 Caps 6.25 to 1-5/8” Hex Drive Cap
6.25 H.D Bullet Shoe, Auger Fork, 6.25 to 4.25 Drive Cap
10.25 H.D Bullet Shoe, 24” Extension, 10.25 to 4.25 Drive Cap
12.25 H.D Bullet Shoe, 12.25 to 4.25 Drive Cap
Shipping cost not included. Call for individual pricing
Package Price: $26,000
DIEDRICH DRILLING TOOLS (Ref#3064Tb)
4-1/4 Hollow Stem Augers 15 @ 5', Bolts for HSA (40), 4-1/4" auger holder, 4-1/4" double adapter, 4-1/4" auger head blade bit (3), 4-1/4" auger head finger bit
6-1/4" Hollow Stem Augers 12 @ 5' and 1 @ 3', auger bolts (40), 6-1/4" hex pin box cap, 6-1/4" pilot bit, 6-1/4" auger holder (3), 6-1/4" auger blade bit
2-7/8" AW rods box pin conn 21 @ 5', 4-1/2" AW core barrel for auger, 4-1/4 AW rod bit, 2-7/8 AW rod closed pulley plate, 2-7/8 AW rod open pulley plate, 2-3/4" AW water swivel, 2-3/5 AW rod drag bit, AW pin connect swivel, 4-1/4" AW rod solid bit, 2-7/8 AW rod cap adapter
3" Shelby Tube Head, 3" Shelby Tubes (44), 3" extruder holder, 2" split spoon sampler 4 @ 2', 2" AW head for sampler, 2" threaded shoe end (2)
3-1/2" Solid Flight Auger 12 @ 5', 1-1/8" hex pin to box conn, 3-1/2" auger holder (3), 3-1/2" U pins for augers (20), 4-1/2" auger bit